You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Did I damage My Vesc? by Kent Church on Tue, 2022-01-11 04:47 |
1 |
by skyline1970 Wed, 2022-01-19 09:46 |
General discussion | |
|
Best practice for controlling VESC with high speed PWM by arsenix on Sun, 2022-01-09 18:29 |
1 |
by skyline1970 Wed, 2022-01-19 09:39 |
General discussion | |
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees on Tue, 2022-01-18 22:57 |
by christian.lees Tue, 2022-01-18 22:57 |
General discussion | ||
|
Need Help with single FSESC running a BDUAV 6384 120KV & 12v SLA Batt Setup by KJB on Fri, 2022-01-07 02:43 |
1 |
by skyline1970 Tue, 2022-01-18 10:39 |
General discussion | |
|
ESC FS75100 by myck33 on Fri, 2021-12-31 14:17 |
2 |
by jaykup Sun, 2022-01-16 22:43 |
VESC Firmware | |
|
Rough Motor Running When USB Cable At Vesc Tool is Disconnected by David Cunliffe on Sun, 2022-01-16 11:42 |
11 |
by David Cunliffe Sun, 2022-01-16 15:32 |
General discussion | |
|
BLDC_SPEED_CONTROL_CURRENT by salviador on Fri, 2022-01-14 16:32 |
by salviador Fri, 2022-01-14 16:32 |
VESC Firmware | ||
|
I Need Some Guidance With My Schematic 16s 50a by qwerasdf on Sat, 2022-01-01 15:04 |
6 |
by mckenzie.keith Fri, 2022-01-14 04:39 |
Third Party Hardware | |
|
Failure in Motor Set Up by Toshi Sharma on Tue, 2022-01-11 15:19 |
9 |
by frank Thu, 2022-01-13 14:15 |
General discussion | |
|
E-bike with Ubox board by tailele on Wed, 2020-11-18 11:48 |
6 |
by kevingraehl Thu, 2022-01-13 09:24 |
Third Party Hardware | |
|
I cant get my scooter to work correct it make some strange sounds by vallsta on Sun, 2021-05-16 03:19 |
39 |
by svs Thu, 2022-01-13 07:53 |
General discussion | |
|
PWM timer issues on high voltage by pegasus-aero on Tue, 2022-01-04 01:39 |
3 |
by pegasus-aero Thu, 2022-01-13 00:37 |
Third Party Hardware | |
|
Using VESC for a Linear Motor by Toshi Sharma on Wed, 2022-01-12 13:11 |
by Toshi Sharma Wed, 2022-01-12 13:11 |
General discussion | ||
|
Slight stutter when sensor mode turns off by rg12 on Wed, 2022-01-05 01:18 |
4 |
by frank Mon, 2022-01-10 08:21 |
General discussion | |
|
Switching frequency factor 2 lower by Elwin on Sat, 2021-11-13 22:48 |
10 |
by Elwin Sun, 2022-01-09 08:31 |
General discussion | |
|
FOC parameter trouble by CTSchorsch on Sat, 2022-01-08 00:20 |
7 |
by CTSchorsch Sat, 2022-01-08 15:13 |
Third Party Hardware | |
|
Flipsky 4.2 ESC go BOOM!?! by arranto12 on Thu, 2022-01-06 20:36 |
1 |
by frank Fri, 2022-01-07 10:58 |
General discussion | |
|
Serial port errors with VESC Tool 3.00 and Flipsky FSESC 7550 by mckenzie.keith on Thu, 2022-01-06 02:24 |
1 |
by mckenzie.keith Thu, 2022-01-06 18:54 |
VESC Tool | |
|
Broken drive at 4000erpm by craig w on Thu, 2022-01-06 01:09 |
1 |
by frank Thu, 2022-01-06 10:51 |
VESC6 Beta | |
|
Getting RPM data from VESC 4.12 by EmirDns on Wed, 2022-01-05 21:20 |
by EmirDns Wed, 2022-01-05 21:20 |
VESC Original Hardware |
Pages
