You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Motor clicking and not spinning after setup wizard by dfelz on Fri, 2020-04-03 03:51 |
6 |
by brian adilman Wed, 2022-01-26 13:36 |
VESC Tool | |
|
VESC Tool on Windows 10 32 Bit doesn't open by Red_Speedster on Mon, 2021-05-31 16:33 |
2 |
by frank Wed, 2022-01-26 08:21 |
VESC Tool | |
|
Stormcore 60D+ loses drive on one side by Big_McLargeHuge on Wed, 2022-01-26 05:01 |
1 |
by Big_McLargeHuge Wed, 2022-01-26 05:21 |
General discussion | |
|
Loud noises at some RPMs by isso777 on Mon, 2022-01-24 16:05 |
2 |
by isso777 Tue, 2022-01-25 10:36 |
General discussion | |
|
Are the FOC PID values for discrete or continuous time controllers? by ward on Fri, 2022-01-21 15:55 |
4 |
by Elwin Tue, 2022-01-25 07:48 |
VESC Original Hardware | |
|
Minimum System Requirements for VESC Tool 3.01 under Windows by j.konrad on Mon, 2022-01-24 21:48 |
by j.konrad Mon, 2022-01-24 21:48 |
VESC Tool | ||
|
Powering a Beckhoff AM3100 Synchronus Servomotor with FOC by Michael Hamm on Mon, 2022-01-24 10:42 |
1 |
by frank Mon, 2022-01-24 12:36 |
General discussion | |
|
Connecting AMT203 to Flipsky 4.20 ESC by kgeo0003 on Mon, 2022-01-24 06:44 |
by kgeo0003 Mon, 2022-01-24 09:00 |
General discussion | ||
|
How can I get current data from VESC to stm32f446re by hyedo on Sun, 2022-01-23 19:38 |
by hyedo Sun, 2022-01-23 19:38 |
General discussion | ||
|
Maximum Motor RPM will not reached by Skyver on Sun, 2022-01-23 10:53 |
by Skyver Sun, 2022-01-23 10:53 |
General discussion | ||
|
MOSFET failure and replacement, stormcore 60d by Airatic on Wed, 2022-01-19 11:36 |
4 |
by j.konrad Sat, 2022-01-22 01:17 |
General discussion | |
|
new vesc 6 FW update by Shwepsss on Thu, 2022-01-20 20:26 |
1 |
by Shwepsss Fri, 2022-01-21 15:20 |
VESC Firmware | |
|
PAS app: limit current depending on actual velocity by dpeinado on Fri, 2022-01-21 13:49 |
by dpeinado Fri, 2022-01-21 13:49 |
VESC Firmware | ||
|
Vesc Tool Mobile can't update Vesc Firmware by Happy Giraffe on Wed, 2022-01-19 21:48 |
2 |
by Happy Giraffe Thu, 2022-01-20 23:50 |
VESC Tool | |
|
Anti cogging, suppressing torque ripple? by Alistair Goodman on Wed, 2022-01-19 11:33 |
4 |
by Alistair Goodman Thu, 2022-01-20 11:11 |
General discussion | |
|
Max OSX version by emmaanuel on Tue, 2017-09-05 13:03 |
6 |
by briona112 Thu, 2022-01-20 05:27 |
VESC Tool | |
|
questions about "RUN DETECTION" by yuri12 on Thu, 2022-01-20 04:30 |
by yuri12 Thu, 2022-01-20 04:30 |
VESC Tool | ||
|
Stream UART Telemetry without a Request by AlexBenn on Thu, 2022-01-20 02:47 |
by AlexBenn Thu, 2022-01-20 02:47 |
VESC Firmware | ||
|
firm ware error 75_300 by yuri12 on Wed, 2022-01-19 09:50 |
1 |
by frank Wed, 2022-01-19 13:46 |
VESC Firmware | |
|
Did I damage My Vesc? by Kent Church on Tue, 2022-01-11 04:47 |
1 |
by skyline1970 Wed, 2022-01-19 09:46 |
General discussion |
Pages
