You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Where to find codelines for speed and position control structure by kianK on Tue, 2022-03-01 15:25 |
by kianK Thu, 2022-03-03 12:23 |
VESC Firmware | ||
|
VESC100/250; RPM Pulse input; antispark precharge by tobiokanobi on Mon, 2022-02-28 11:56 |
7 |
by tobiokanobi Thu, 2022-03-03 11:22 |
General discussion | |
|
Best Throttle and break level by ardillolambo on Wed, 2022-03-02 18:29 |
by ardillolambo Wed, 2022-03-02 18:29 |
General discussion | ||
|
Axial Flux motor control mode by ardillolambo on Wed, 2022-03-02 13:59 |
4 |
by ardillolambo Wed, 2022-03-02 18:25 |
VESC Original Hardware | |
|
Emergency Stop SSR - Blowing up Microcontroller by J_W97 on Tue, 2022-03-01 14:46 |
5 |
by frank Tue, 2022-03-01 20:19 |
General discussion | |
|
VCC-GND short by caliber interconnect on Sat, 2022-02-26 13:10 |
4 |
by caliber interconnect Tue, 2022-03-01 10:42 |
VESC Original Hardware | |
|
When SWD Program Connect Fails by canoeman on Mon, 2022-02-28 18:32 |
by canoeman Mon, 2022-02-28 18:32 |
General discussion | ||
|
Can't receive status message via CAN bus by IanG on Mon, 2020-04-13 03:50 |
4 |
by olivierabristol Sun, 2022-02-27 08:31 |
General discussion | |
|
RT Data, v3.01, Amazon Fire Tablet (sideloaded) by j.konrad on Thu, 2022-02-24 14:51 |
2 |
by j.konrad Fri, 2022-02-25 14:14 |
VESC Tool | |
|
Dissimilar motor testing by geofrancis on Thu, 2022-02-24 16:54 |
by geofrancis Thu, 2022-02-24 16:57 |
General discussion | ||
|
hysteresis related issue in mcconf and mcpwm_foc.c by masifsr on Thu, 2022-02-24 13:14 |
1 |
by j.konrad Thu, 2022-02-24 14:52 |
General discussion | |
|
VESC for electric scooter by eyup on Tue, 2022-02-22 13:52 |
1 |
by Filip Kinl Thu, 2022-02-24 13:35 |
General discussion | |
|
Writing value to both VESCs on FocFox Unity by agraham on Wed, 2022-02-23 21:45 |
2 |
by benjamin Thu, 2022-02-24 10:57 |
VESC Tool | |
|
MakerX 75/200 - destroyed USB-Port by jangrik on Wed, 2022-02-23 22:01 |
1 |
by jangrik Thu, 2022-02-24 09:49 |
Third Party Hardware | |
|
Difference between ERPM and Duty Cycle by dormanae on Wed, 2022-02-23 17:21 |
1 |
by j.konrad Thu, 2022-02-24 02:08 |
General discussion | |
|
Spintend 75V 100A ubox -Split AD-socket? by Bucket_Residence on Wed, 2022-02-23 22:57 |
by Bucket_Residence Wed, 2022-02-23 22:57 |
Third Party Hardware | ||
|
Discrepancies between VESC Tool 3.01 Motor Settings & XML config file by j.konrad on Sat, 2022-01-15 22:13 |
3 |
by benjamin Mon, 2022-02-21 22:17 |
VESC Tool | |
|
About this forum by benjamin on Tue, 2020-03-17 10:21 |
2 |
by clamdad Mon, 2022-02-21 15:12 |
VESC Development and Beta Testing | |
|
Why use sensorless if the motor has sensors? by j.konrad on Thu, 2022-02-17 14:25 |
4 |
by j.konrad Mon, 2022-02-21 15:06 |
General discussion | |
|
Get Current over CAN bus by chriswei on Thu, 2019-05-16 13:57 |
4 |
by spacewalker Mon, 2022-02-21 08:25 |
VESC Firmware |
Pages
