You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Some small problems with the VESC 6 and the VESC Tool V 0.87 by JL2579 on Thu, 2018-01-11 16:27 |
2 |
by JL2579 Tue, 2018-01-16 16:58 |
Feature Requests | |
|
bootloader destroied by notger on Tue, 2017-09-19 19:55 |
3 |
by dinamee Sat, 2018-01-13 10:09 |
General discussion | |
|
AVERAGE ERPM (Max) Setting for dual vescs by Paul15578 on Fri, 2018-01-12 03:04 |
by Paul15578 Fri, 2018-01-12 03:04 |
Feature Requests | ||
|
Vesc_tool OVER_TEMP_FET by XIII on Thu, 2018-01-11 17:26 |
by XIII Thu, 2018-01-11 17:26 |
VESC Tool | ||
|
VESC tool "GUI" issue. by Roger Wolff on Tue, 2018-01-02 15:13 |
2 |
by ThierryGTLTS Wed, 2018-01-10 17:38 |
VESC Tool | |
|
encoder detection by RSR on Tue, 2017-07-11 10:06 |
3 |
by Benjamin Mahony Wed, 2018-01-10 01:43 |
VESC6 Beta | |
|
FOC and extremely low speeds do not look sinusoidal by wdaehn on Wed, 2017-11-29 21:33 |
11 |
by Benjamin Mahony Wed, 2018-01-10 01:19 |
General discussion | |
|
(Open source) BMS by soltesz on Mon, 2017-12-18 00:26 |
2 |
by Pimousse Mon, 2018-01-08 16:26 |
Third Party Hardware | |
|
Calculation of Current and Voltage by Christian on Tue, 2017-12-12 10:12 |
5 |
by Roger Wolff Sun, 2018-01-07 15:41 |
VESC Firmware | |
|
vesc from flier by Doublewave on Sat, 2017-12-30 10:15 |
1 |
by josh Thu, 2018-01-04 04:32 |
VESC Original Hardware | |
|
Motor rotation direction by e-biker on Fri, 2017-12-22 15:02 |
2 |
by e-biker Tue, 2018-01-02 13:15 |
General discussion | |
|
Bug: Tachometer does not change when handbrake is turned on by wdaehn on Mon, 2017-12-25 10:12 |
by wdaehn Mon, 2017-12-25 10:12 |
VESC Firmware | ||
|
Positional Control, Hall Sensor by wdaehn on Fri, 2017-12-08 15:02 |
4 |
by wdaehn Mon, 2017-12-25 09:46 |
General discussion | |
|
Merry Christmas! by frank on Fri, 2017-12-22 14:31 |
4 |
by ThierryGTLTS Sun, 2017-12-24 14:34 |
General discussion | |
|
Motor detection failed/ 0 faults by jnweb29 on Sat, 2017-12-23 21:07 |
by jnweb29 Sat, 2017-12-23 21:07 |
VESC Tool | ||
|
VESC 6.0 Hardware Shows Up As HW 410 in VESC-Tool by FWachter on Thu, 2017-12-21 20:51 |
1 |
by wdaehn Fri, 2017-12-22 08:22 |
VESC Firmware | |
|
Flux linkage observer @ low speed by soltesz on Sun, 2017-12-17 16:33 |
9 |
by benjamin Thu, 2017-12-21 10:17 |
VESC Firmware | |
|
VESC hardware schematics by cromoly on Tue, 2017-11-28 04:44 |
4 |
by ThierryGTLTS Tue, 2017-12-19 14:03 |
VESC Original Hardware | |
|
Motor shaft machining advices are welcome! by ThierryGTLTS on Tue, 2017-11-14 17:40 |
5 |
by William Yates Mon, 2017-12-18 18:22 |
The VESC-Project | |
|
Two Motors on same Shaft by Giga93 on Thu, 2017-12-14 10:12 |
5 |
by ThierryGTLTS Sun, 2017-12-17 13:20 |
General discussion |
Pages
