You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Write Motor Configuration - not working by acherpil on Tue, 2018-12-04 10:23 |
by acherpil Tue, 2018-12-04 16:43 |
VESC Firmware | ||
|
Lawn mower by charper on Mon, 2018-12-03 14:25 |
by charper Mon, 2018-12-03 14:25 |
General discussion | ||
|
vesc <-> arduino micro troubleshooting UART issues by fourchette on Mon, 2018-11-26 11:59 |
1 |
by fourchette Mon, 2018-12-03 13:41 |
General discussion | |
|
Older version of VESC Tool by Gas_Sn4ke on Fri, 2018-11-30 09:28 |
by Gas_Sn4ke Fri, 2018-11-30 09:28 |
VESC Tool | ||
|
Fried C51(?) on my VESC 4.12 by spork on Tue, 2018-11-27 07:00 |
6 |
by spork Thu, 2018-11-29 16:43 |
General discussion | |
|
Stall torque in sensorless mode by cromoly on Sun, 2018-11-25 07:54 |
4 |
by spork Thu, 2018-11-29 03:23 |
General discussion | |
|
Using reverse with a spare channel by spork on Mon, 2018-11-26 07:08 |
4 |
by spork Tue, 2018-11-27 06:48 |
General discussion | |
|
Connecting ABI encoder to VESC by Gas_Sn4ke on Mon, 2018-11-26 06:00 |
by Gas_Sn4ke Mon, 2018-11-26 06:00 |
VESC Tool | ||
|
Customization of Firmware by EnricoB on Mon, 2018-11-19 23:01 |
4 |
by EnricoB Sun, 2018-11-25 21:03 |
VESC Firmware | |
|
Duty cycle-what does that control? by cromoly on Sat, 2018-11-24 01:11 |
2 |
by cromoly Sun, 2018-11-25 07:40 |
General discussion | |
|
Auto power shut down by Ecyclist on Thu, 2018-09-20 00:47 |
4 |
by sam.vanratt Sat, 2018-11-24 20:12 |
Feature Requests | |
|
HArd power off switch by jakaranda on Mon, 2018-10-29 11:15 |
3 |
by sam.vanratt Sat, 2018-11-24 18:08 |
General discussion | |
|
USB can not recognize by xiaofeixiak on Sat, 2018-11-24 03:20 |
1 |
by sam.vanratt Sat, 2018-11-24 14:44 |
General discussion | |
|
Encoder over SPI doesn't work on FW3.40: SOLVED by john on Mon, 2018-11-12 09:00 |
2 |
by john Fri, 2018-11-23 16:40 |
General discussion | |
|
LED HW PWM?? by milom on Fri, 2018-11-16 15:29 |
1 |
by benjamin Fri, 2018-11-23 09:57 |
General discussion | |
|
Priority of CAN messages? by hmijail on Sat, 2018-10-27 06:30 |
2 |
by hmijail Fri, 2018-11-23 01:44 |
VESC Firmware | |
|
Max Switching Frequency FOC by tuloski on Thu, 2018-09-13 10:37 |
8 |
by Maxim Gridin Thu, 2018-11-22 21:47 |
VESC Firmware | |
|
Fried Hall Effect Throttle Sensor by cdw3423vesc on Thu, 2018-11-15 05:16 |
2 |
by sam.vanratt Thu, 2018-11-22 20:33 |
General discussion | |
|
VESC TOOL ADC Voltage mapping too low. SOLVED by Ecyclist on Fri, 2018-10-19 22:38 |
5 |
by sam.vanratt Thu, 2018-11-22 20:21 |
General discussion | |
|
Flashing via SWD works, but no green LED or USB enumeration by vpl on Fri, 2018-11-16 17:48 |
1 |
by vpl Wed, 2018-11-21 17:27 |
VESC Original Hardware |
Pages
