You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Flipsky nrf51288 by Idoff on Tue, 2018-12-11 21:33 |
2 |
by frank Mon, 2019-02-18 09:00 |
VESC Tool | |
|
VESC Questions from the newbie by mendez on Fri, 2019-02-08 21:13 |
10 |
by frank Mon, 2019-02-18 08:52 |
General discussion | |
|
information to drive 400kv drone motor on ClosedLoop with AS5047 by Syl2078 on Sun, 2019-02-17 19:20 |
by Syl2078 Sun, 2019-02-17 19:20 |
General discussion | ||
|
Advanced settings for FOC motor detection (flux linkage) by jaghori.sasan on Sun, 2019-02-17 09:34 |
2 |
by jaghori.sasan Sun, 2019-02-17 17:51 |
VESC Tool | |
|
Observer tracking fail by dangminhducnbk on Sun, 2019-02-17 14:09 |
by dangminhducnbk Sun, 2019-02-17 14:09 |
General discussion | ||
|
Struggling in startup BLDC in sensorless mode by dangminhducnbk on Fri, 2019-02-15 03:42 |
2 |
by dangminhducnbk Sun, 2019-02-17 12:48 |
General discussion | |
|
2 vs 3 phase shunts by antonchromjak on Sun, 2018-04-15 13:25 |
13 |
by TechAUmNu Fri, 2019-02-15 18:57 |
General discussion | |
|
Dual Hybrid mode by L.ST on Sun, 2019-01-13 00:24 |
1 |
by vpl Fri, 2019-02-15 13:37 |
VESC Firmware | |
|
3 shunt low side resistor configuration based on VESC 6 by jordanlow on Thu, 2019-02-14 16:42 |
1 |
by TechAUmNu Thu, 2019-02-14 18:31 |
Third Party Hardware | |
|
No connection with vesc by Matthieu van Ra... on Wed, 2019-02-13 18:07 |
8 |
by sam.vanratt Thu, 2019-02-14 15:33 |
General discussion | |
|
Building the vesc firmware in Chibi Studio by chris1seto on Sat, 2019-01-12 02:36 |
1 |
by kinzma Thu, 2019-02-14 09:42 |
General discussion | |
|
Always get Fault:DRV in FOC mode during startup . by stone_1706 on Sat, 2019-02-02 17:35 |
3 |
by stone_1706 Tue, 2019-02-12 03:20 |
General discussion | |
|
SPI Encoder communications with AS5047 by vadimz on Sun, 2018-10-28 16:55 |
3 |
by Guillaume227 Mon, 2019-02-11 23:14 |
VESC Firmware | |
|
Sudden vesc unresponsiveness by nolander on Mon, 2019-01-07 22:29 |
6 |
by Caustic_Zinc Mon, 2019-02-11 09:32 |
VESC Tool | |
|
Sub zero temperature VESC412 issues by jetigm on Fri, 2019-02-08 21:12 |
3 |
by sam.vanratt Sun, 2019-02-10 14:07 |
General discussion | |
|
Is there a complete documentation for the communication protocol between the vesc tool and the board? by aishangmu on Tue, 2018-12-25 09:00 |
2 |
by Caustic_Zinc Fri, 2019-02-08 19:27 |
VESC Tool | |
|
Sensored FOC not working by Jarson on Thu, 2019-01-24 20:03 |
1 |
by Caustic_Zinc Fri, 2019-02-08 19:19 |
VESC Tool | |
|
Where to order plastic sleeve for VESC by braingame26 on Thu, 2019-02-07 16:34 |
by braingame26 Thu, 2019-02-07 16:34 |
Third Party Hardware | ||
|
Dual brushed motors from 1 R/C stick? by VESC1 on Thu, 2019-01-31 06:19 |
5 |
by sam.vanratt Sun, 2019-02-03 16:30 |
General discussion | |
|
Fault:DRV8302 DUAL V4 by Lzx19961014 on Tue, 2018-09-04 11:48 |
3 |
by stone_1706 Sat, 2019-02-02 17:09 |
General discussion |
Pages
