You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Could you recommend me a Button for turn on/off the VESC by aysubscriber@ic... on Tue, 2017-10-03 07:49 |
6 |
by e-nduro Thu, 2019-09-05 00:28 |
General discussion | |
|
UART Safety Feature by jaghori.sasan on Wed, 2019-09-04 18:45 |
by jaghori.sasan Wed, 2019-09-04 18:45 |
VESC Tool | ||
|
vesc tool crashing on 29aug19 - website down/link? by ianp on Fri, 2019-08-30 04:10 |
1 |
by frank Mon, 2019-09-02 11:26 |
VESC Tool | |
|
ESC ceases operation after 40 sec ride by dekafive on Sun, 2019-08-25 22:25 |
1 |
by frank Mon, 2019-09-02 10:50 |
Third Party Hardware | |
|
Incorrect parameter detection by macieksz@pro.onet.pl on Fri, 2019-08-30 16:05 |
by macieksz@pro.onet.pl Fri, 2019-08-30 16:05 |
VESC Tool | ||
|
VESC questions by RDN2003 on Tue, 2019-08-27 23:41 |
1 |
by frank Fri, 2019-08-30 10:09 |
General discussion | |
|
Custom Display Receiver for VESC by WatEvsCevs on Wed, 2019-08-28 02:29 |
1 |
by frank Fri, 2019-08-30 10:03 |
General discussion | |
|
VESC for turbomachine testing - max ERPM? by batdan on Tue, 2019-08-13 16:58 |
2 |
by batdan Tue, 2019-08-27 16:48 |
General discussion | |
|
Logging IMU Data over UART by stefan_novige on Mon, 2019-08-19 18:28 |
6 |
by pf26 Tue, 2019-08-27 13:44 |
General discussion | |
|
VESC CAN Status message interpretation by harsha008 on Wed, 2019-01-09 17:56 |
1 |
by bluesquall Tue, 2019-08-27 01:59 |
General discussion | |
|
Sensorless BLDC start problem by MikeStros on Tue, 2019-07-30 11:49 |
2 |
by dekafive Fri, 2019-08-23 21:46 |
General discussion | |
|
foc with encoder fails to run smoothly by jdn on Thu, 2019-08-22 12:26 |
by jdn Thu, 2019-08-22 15:47 |
General discussion | ||
|
Is it possible to stop a motor at one exact desired location without hall sensor? by vimi94 on Thu, 2019-08-15 10:58 |
2 |
by vimi94 Tue, 2019-08-20 13:37 |
VESC Tool | |
|
Problems with flashing firmware to FLIPSKY ESC by xx11xx on Wed, 2019-08-14 18:10 |
1 |
by kinzma Tue, 2019-08-20 07:56 |
VESC Firmware | |
|
Vesc to Uart (Nextion display) by g1tana on Mon, 2019-08-19 15:29 |
by g1tana Mon, 2019-08-19 15:30 |
General discussion | ||
|
Trying to make motor-control work for predetermined motions, could use some help by Davideo on Fri, 2019-08-16 01:20 |
1 |
by s0313045 Mon, 2019-08-19 05:12 |
General discussion | |
|
Wrong Motor detection values after STM swap dual vesc 6 by Micro on Sun, 2019-08-18 01:59 |
by Micro Sun, 2019-08-18 02:14 |
VESC Tool | ||
|
Simulating controller accurately by TechAUmNu on Fri, 2019-08-16 15:35 |
by TechAUmNu Fri, 2019-08-16 15:35 |
General discussion | ||
|
understanding switching frequency and dutycycle by speed3r on Thu, 2019-08-08 13:36 |
3 |
by speed3r Thu, 2019-08-15 09:26 |
General discussion | |
|
VESC 4.12 - Data loss on power off by da_rul0r on Wed, 2019-08-14 16:43 |
2 |
by da_rul0r Thu, 2019-08-15 08:33 |
VESC Original Hardware |
Pages
