You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Do I need a motor with Hall sensor to use Vesc tool? by greew on Sun, 2020-05-31 06:48 |
by greew Sun, 2020-05-31 06:48 |
General discussion | ||
Why not using interrupt for Hall signal detection? by kuan on Sun, 2021-01-03 09:51 |
by kuan Sun, 2021-01-03 09:51 |
General discussion | ||
Help with FOC/PID parameter by CTSchorsch on Thu, 2020-01-23 21:57 |
by CTSchorsch Thu, 2020-01-23 21:57 |
General discussion | ||
D vs omega control by rsarver on Wed, 2021-03-17 14:44 |
by rsarver Wed, 2021-03-17 14:44 |
VESC Tool | ||
VESC specialist required. by BlackPanthera on Mon, 2022-07-18 17:11 |
by BlackPanthera Mon, 2022-07-18 17:11 |
General discussion | ||
aggressive throttle by Sandro luis on Sun, 2024-05-05 04:42 |
by Sandro luis Sun, 2024-05-05 04:42 |
General discussion | ||
Older version of VESC Tool by Gas_Sn4ke on Fri, 2018-11-30 09:28 |
by Gas_Sn4ke Fri, 2018-11-30 09:28 |
VESC Tool | ||
foc with encoder fails to run smoothly by jdn on Thu, 2019-08-22 12:26 |
by jdn Thu, 2019-08-22 15:47 |
General discussion | ||
How to set dead time on BLDC mode? by AllenFF on Wed, 2020-04-15 03:30 |
by AllenFF Mon, 2020-04-27 15:34 |
General discussion | ||
sick srm50 absolute encoder, I don't know how to configure it by Davidson SIlvei... on Mon, 2024-04-22 21:45 |
by Davidson SIlvei... Mon, 2024-04-22 21:45 |
VESC Tool | ||
How to increase the +/-165A rms current limit to 250A+ rms (350-400A peak) by ev_motors on Sat, 2018-04-28 10:18 |
by ev_motors Sat, 2018-04-28 10:18 |
General discussion | ||
Move FAULT pin to GPIOD_PIN2 by CTSchorsch on Tue, 2018-09-04 10:13 |
by CTSchorsch Tue, 2018-09-04 10:13 |
VESC Firmware | ||
UART write read arduino by matiller on Sat, 2019-06-01 20:18 |
by matiller Sat, 2019-06-01 20:18 |
VESC Tool | ||
Target VESC has no space to be flashed with ST-Link by Thi4g0tk on Sun, 2021-03-28 14:50 |
by Thi4g0tk Sun, 2021-03-28 14:50 |
Third Party Hardware | ||
PAS only one signal + BLE by sifourquier on Fri, 2021-12-31 19:08 |
by sifourquier Fri, 2021-12-31 19:08 |
General discussion | ||
AVERAGE ERPM (Max) Setting for dual vescs by Paul15578 on Fri, 2018-01-12 03:04 |
by Paul15578 Fri, 2018-01-12 03:04 |
Feature Requests | ||
Safety Signal by Flepple on Thu, 2020-11-26 12:17 |
by Flepple Mon, 2020-11-30 16:17 |
VESC Firmware | ||
vesc, firmware, motor parameter calibration files? by dcameron on Fri, 2022-11-18 22:19 |
by dcameron Fri, 2022-11-18 22:19 |
General discussion | ||
Speed control issues w. hub motors by akerblad on Sun, 2019-04-07 17:22 |
by akerblad Sun, 2019-04-07 17:22 |
General discussion | ||
anti theft possible? by hummina on Tue, 2021-02-23 07:44 |
by hummina Tue, 2021-02-23 07:44 |
General discussion |