You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
F50-300 (Design Not Tested yet) by mrendu43 on Tue, 2021-03-09 11:49 |
13 |
by mrendu43 Sat, 2021-05-01 17:15 |
Third Party Hardware | |
|
Flipsky ADC always high by Bariiq on Fri, 2019-04-19 11:46 |
1 |
by andrecorreia Fri, 2021-04-30 01:22 |
Third Party Hardware | |
|
Why i cant insert a topic? by SafrdA on Thu, 2021-04-29 20:41 |
by SafrdA Thu, 2021-04-29 20:41 |
General discussion | ||
|
VESC 5.01 + ESP8266 + UART no data received? by i-make-robots on Wed, 2020-07-15 20:09 |
3 |
by Nickklas Tue, 2021-04-27 12:08 |
General discussion | |
|
tips for power design by antonchromjak on Mon, 2021-04-12 18:34 |
5 |
by vadicus Tue, 2021-04-27 03:01 |
Third Party Hardware | |
|
Problem with VESC Tool vs BLDC FW version by Reidar Jortveit on Mon, 2021-04-26 14:39 |
1 |
by Reidar Jortveit Mon, 2021-04-26 14:49 |
VESC Tool | |
|
no effect on set erpm/speed limit by xenon321 on Sat, 2021-04-24 20:43 |
by xenon321 Sun, 2021-04-25 16:53 |
VESC Tool | ||
|
VESC 75/300 R2 with R1 Firmware by frank on Thu, 2019-11-28 09:39 |
1 |
by Henque19 Sat, 2021-04-24 22:48 |
VESC Firmware | |
|
Maytech VESC 6 FOC turn off without fault at high erpm, blower by gabrield on Fri, 2020-05-15 01:16 |
2 |
by ImperialSB Thu, 2021-04-22 17:54 |
Third Party Hardware | |
|
Is the Vesc 5 mkIII capable of 13s li-Ion (fully charged 54,6V) by Pelle on Sun, 2020-04-12 12:09 |
4 |
by danilolattaro Thu, 2021-04-22 14:50 |
General discussion | |
|
DC Motor Settings (24v PowerWheels) by KirkusMaximus on Thu, 2021-04-22 00:17 |
by KirkusMaximus Thu, 2021-04-22 00:18 |
VESC Tool | ||
|
HD60 CAN Resistor by BEWA on Wed, 2021-04-21 14:56 |
by BEWA Wed, 2021-04-21 14:56 |
VESC Original Hardware | ||
|
two motors one ppm for throttle and one for the direction? by Robby Ertmann on Wed, 2021-04-21 13:48 |
by Robby Ertmann Wed, 2021-04-21 13:48 |
VESC Tool | ||
|
Strange behavior of limited current by erylon on Fri, 2021-04-16 22:56 |
1 |
by Katt Tue, 2021-04-20 23:21 |
General discussion | |
|
120V dual VESC for E-scooter by Daniel Kaminski on Mon, 2021-04-05 17:21 |
6 |
by Daniel Kaminski Tue, 2021-04-20 12:17 |
General discussion | |
|
Windows application by roeebloch on Mon, 2021-04-19 21:08 |
by roeebloch Mon, 2021-04-19 21:08 |
General discussion | ||
|
What are the meaning of some of the MCCONF values... by jackherer on Thu, 2021-04-15 17:25 |
3 |
by hideo040401 Mon, 2021-04-19 19:58 |
VESC Firmware | |
|
eRPM limited to 40600 or so on 6.6 by Dan Slanker on Fri, 2021-04-16 01:22 |
4 |
by TechAUmNu Mon, 2021-04-19 11:10 |
General discussion | |
|
Is there a way to deactivate roll to start function FW 5.02 by Philo on Fri, 2021-04-16 22:28 |
by Philo Sun, 2021-04-18 11:57 |
VESC Firmware | ||
|
Disabling brakes when ADC is set to zero by dsuresh on Wed, 2021-04-14 23:36 |
1 |
by diler Sat, 2021-04-17 11:01 |
General discussion |
Pages
