You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Have i bricked my flipsky FSESC 4.20? by olletj on Sat, 2022-01-22 18:03 |
2 |
by olletj Mon, 2022-01-31 21:18 |
Third Party Hardware | |
|
Golden Motor HPM48-5000, reconciling winding R & L values by j.konrad on Sat, 2022-01-15 22:09 |
24 |
by j.konrad Mon, 2022-01-31 15:15 |
General discussion | |
|
Loss of control during regen by mckenzie.keith on Fri, 2022-01-28 02:42 |
3 |
by frank Sat, 2022-01-29 10:34 |
VESC Firmware | |
|
Limiting Down hill speed by dbau on Sat, 2022-01-29 06:54 |
by dbau Sat, 2022-01-29 09:19 |
General discussion | ||
|
Motor cogging by blox11 on Thu, 2022-01-27 03:07 |
6 |
by blox11 Fri, 2022-01-28 21:37 |
General discussion | |
|
AS5047 with VESC75/300 by hpb66 on Mon, 2021-11-29 10:11 |
5 |
by canoeman Fri, 2022-01-28 20:17 |
VESC Original Hardware | |
|
Using 13s battery on flipsky FSESCs. Is it safe? by Murilo on Thu, 2022-01-27 02:59 |
2 |
by Murilo Thu, 2022-01-27 20:20 |
General discussion | |
|
Motor shutting off due to FAULT_CODE_ABS_OVER_CURRENT by isso777 on Mon, 2022-01-24 13:56 |
5 |
by canoeman Thu, 2022-01-27 18:12 |
General discussion | |
|
current of holding by reff on Thu, 2022-01-27 16:38 |
by reff Thu, 2022-01-27 16:39 |
VESC Tool | ||
|
The engine stopped spinning after updating firmware by brian adilman on Wed, 2022-01-26 17:40 |
by brian adilman Wed, 2022-01-26 19:15 |
VESC Firmware | ||
|
The engine stopped spinning after updating firmware by brian adilman on Wed, 2022-01-26 17:40 |
by brian adilman Wed, 2022-01-26 19:15 |
VESC Tool | ||
|
Motor clicking and not spinning after setup wizard by dfelz on Fri, 2020-04-03 03:51 |
6 |
by brian adilman Wed, 2022-01-26 13:36 |
VESC Tool | |
|
VESC Tool on Windows 10 32 Bit doesn't open by Red_Speedster on Mon, 2021-05-31 16:33 |
2 |
by frank Wed, 2022-01-26 08:21 |
VESC Tool | |
|
Stormcore 60D+ loses drive on one side by Big_McLargeHuge on Wed, 2022-01-26 05:01 |
1 |
by Big_McLargeHuge Wed, 2022-01-26 05:21 |
General discussion | |
|
Loud noises at some RPMs by isso777 on Mon, 2022-01-24 16:05 |
2 |
by isso777 Tue, 2022-01-25 10:36 |
General discussion | |
|
Are the FOC PID values for discrete or continuous time controllers? by ward on Fri, 2022-01-21 15:55 |
4 |
by Elwin Tue, 2022-01-25 07:48 |
VESC Original Hardware | |
|
Minimum System Requirements for VESC Tool 3.01 under Windows by j.konrad on Mon, 2022-01-24 21:48 |
by j.konrad Mon, 2022-01-24 21:48 |
VESC Tool | ||
|
Powering a Beckhoff AM3100 Synchronus Servomotor with FOC by Michael Hamm on Mon, 2022-01-24 10:42 |
1 |
by frank Mon, 2022-01-24 12:36 |
General discussion | |
|
Connecting AMT203 to Flipsky 4.20 ESC by kgeo0003 on Mon, 2022-01-24 06:44 |
by kgeo0003 Mon, 2022-01-24 09:00 |
General discussion | ||
|
How can I get current data from VESC to stm32f446re by hyedo on Sun, 2022-01-23 19:38 |
by hyedo Sun, 2022-01-23 19:38 |
General discussion |
Pages
