You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Fault code sensor 1 by krille on Sat, 2022-07-23 16:31 |
1 |
by skyline1970 Thu, 2022-11-24 21:08 |
General discussion | |
Hall effect sensor type for Flipsky 4.20 by braydinjones on Sun, 2022-07-24 01:06 |
1 |
by skyline1970 Thu, 2022-11-24 21:06 |
General discussion | |
Open ESC for sensored 1/12 pan cars? by DocTrucker on Tue, 2022-08-02 08:33 |
1 |
by skyline1970 Thu, 2022-11-24 21:02 |
General discussion | |
VESC - HIL / DRV8301 SPI - Problems? by mm_iem on Tue, 2022-08-09 12:34 |
1 |
by skyline1970 Thu, 2022-11-24 20:54 |
VESC Firmware | |
Problem to configure my esc with PWM-signal by Lucar on Wed, 2022-09-14 10:05 |
1 |
by skyline1970 Thu, 2022-11-24 20:26 |
VESC Tool | |
Diagnosing FSESC4.20 dead/weird phase (?) by josephduchesne on Sun, 2022-09-18 23:52 |
1 |
by skyline1970 Thu, 2022-11-24 20:23 |
Third Party Hardware | |
How to increase power ? by boursomaster on Sat, 2022-09-24 21:19 |
1 |
by skyline1970 Thu, 2022-11-24 20:19 |
General discussion | |
PPM Pulselength mapping by Shaftdriver on Tue, 2022-10-04 19:50 |
1 |
by skyline1970 Thu, 2022-11-24 20:15 |
VESC Tool | |
Vesc edu 6 with 2800Kv brushless motor speed control by siklopentan on Sat, 2022-10-15 14:34 |
1 |
by skyline1970 Thu, 2022-11-24 20:12 |
General discussion | |
Flipsky 75200 + Flipsky 85135 12kw only 2kw output by giver on Thu, 2022-10-27 21:00 |
1 |
by skyline1970 Thu, 2022-11-24 20:08 |
Third Party Hardware | |
VESC 75/300 with 120100 motor for hydraulic pump unit by chundri on Mon, 2022-10-31 12:12 |
1 |
by skyline1970 Thu, 2022-11-24 20:04 |
VESC Original Hardware | |
Motor Driver Voltage Spike Problem by sersam on Sat, 2022-11-12 19:23 |
1 |
by skyline1970 Thu, 2022-11-24 20:00 |
General discussion | |
Vesc efficiency through log (.CSV) by th0masrtg on Tue, 2022-11-22 10:08 |
by th0masrtg Tue, 2022-11-22 10:08 |
VESC Tool | ||
Negative Current Spikes with Unloaded Hub Motor at Full Throttle (95% Duty) by vadicus on Wed, 2021-02-10 00:49 |
2 |
by Andreaa23 Tue, 2022-11-22 05:55 |
General discussion | |
Flipsky 75100 e-bike ,controller gives low amperage at low rpm ,edit solved by mehmetoz1980 on Sun, 2022-11-20 17:55 |
2 |
by mehmetoz1980 Mon, 2022-11-21 13:29 |
General discussion | |
what is HFI in the VESC? by dcameron on Sat, 2022-11-19 00:14 |
2 |
by dcameron Mon, 2022-11-21 02:07 |
General discussion | |
Using VESC remote with non-VESC ESC by Ptkend on Tue, 2022-11-15 17:21 |
6 |
by Ptkend Sun, 2022-11-20 14:04 |
General discussion | |
Trampa 100/250 with one old brushed DC motor....how can i change the motor spin direction????plz help!!! by Asi on Fri, 2022-11-18 12:45 |
3 |
by frank Sat, 2022-11-19 14:55 |
General discussion | |
vesc, firmware, motor parameter calibration files? by dcameron on Fri, 2022-11-18 22:19 |
by dcameron Fri, 2022-11-18 22:19 |
General discussion | ||
Internal Data Logging by KS0n on Thu, 2018-01-11 19:58 |
8 |
by vadicus Thu, 2022-11-17 21:42 |
Feature Requests |