You are here

Active forum topics

Topic Replies Last postsort ascending Forum
Normal topic dual vesc
by badger1666 on Fri, 2018-09-21 09:10
4 by badger1666
Sat, 2018-09-29 15:45
General discussion
Normal topic PYVESC UART Issues
by goethe on Fri, 2017-12-29 21:36
13 by petertaylor
Tue, 2018-09-25 10:06
VESC Firmware
Normal topic Maytech VESC 4.10 UART issues
by LogixCraft on Tue, 2018-09-25 03:13
by LogixCraft
Tue, 2018-09-25 03:13
Third Party Hardware
Normal topic Maytech VESC keeps startup spinning slowly
by Snorreman on Mon, 2018-09-24 09:57
by Snorreman
Mon, 2018-09-24 09:57
Third Party Hardware
Normal topic HW 4.12 Change low voltage cutoff
by subodh.malgonde on Tue, 2018-09-18 07:31
7 by TheFallen
Thu, 2018-09-20 09:51
VESC Original Hardware
Normal topic Custom 12S VESC seems to be power limiting or something
by nickw1881 on Sat, 2018-08-25 07:40
4 by nickw1881
Tue, 2018-09-18 05:56
Third Party Hardware
Normal topic Problems with a small motor
by tuloski on Thu, 2018-09-13 17:27
3 by tuloski
Mon, 2018-09-17 18:21
VESC Firmware
Normal topic Compiling in a different config.
by Roger Wolff on Mon, 2018-09-17 17:07
1 by TechAUmNu
Mon, 2018-09-17 17:12
General discussion
Normal topic VESC Tool 0.87
by pieschie on Sun, 2018-08-26 12:38
3 by Roger Wolff
Sun, 2018-09-16 12:00
VESC Tool
Normal topic Show actual encoder RPM
by Enak on Fri, 2017-09-08 01:05
2 by Roger Wolff
Sun, 2018-09-16 09:47
Feature Requests
Normal topic Speed control tuning for 500-1000 RPM
by vadimz on Sun, 2018-09-02 18:09
2 by vadimz
Sat, 2018-09-15 14:08
General discussion
Normal topic FAULT_CODE_DRV Motor not spinning
by Mightyorc on Sat, 2018-09-15 03:36
by Mightyorc
Sat, 2018-09-15 03:36
General discussion
Normal topic Maytech esc 5V rail reads 0.5v
by hhhhghg on Fri, 2018-09-14 13:23
by hhhhghg
Fri, 2018-09-14 13:23
Third Party Hardware
Normal topic Cut-out at >40A
by thewho on Thu, 2018-09-13 20:24
by thewho
Thu, 2018-09-13 20:24
General discussion
Normal topic FOC detection needs load?
by tuloski on Thu, 2018-09-13 10:19
1 by TechAUmNu
Thu, 2018-09-13 12:26
VESC Tool
Normal topic AS5048A and the AS5047D Problems.
by raess on Wed, 2018-04-04 14:05
2 by liqikai
Thu, 2018-09-13 10:47
General discussion
Normal topic Cannot get any PPM signals from Arduino. Or is it just the VESC tool?
by MaxMaker1 on Thu, 2018-06-21 23:06
4 by tuloski
Thu, 2018-09-13 09:36
VESC Tool
Normal topic Prevent Wheel-slip by low-pass filtering duty cycle output
by AlexBenn on Thu, 2018-09-13 07:50
by AlexBenn
Thu, 2018-09-13 07:50
VESC Firmware
Normal topic Flipsky 4.12 Vesc in FOC mode?
by Jonny254 on Sat, 2018-09-08 11:25
3 by Jonny254
Thu, 2018-09-13 05:48
Third Party Hardware
Normal topic Single shunt
by andreas on Wed, 2018-09-12 22:17
by andreas
Wed, 2018-09-12 22:17
Feature Requests

Pages

Subscribe to Active forum topics