You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Cut off after reaching Max. Duty Cycle by toboli on Thu, 2023-06-01 22:54 |
2 |
by toboli Sat, 2023-07-01 13:32 |
General discussion | |
|
Massive overshoot in BLDC current control by chris1seto on Tue, 2019-04-09 20:10 |
2 |
by frank Thu, 2019-04-11 11:40 |
Third Party Hardware | |
|
Brake lever Cutoff switch seperate from Regen braking/throttle wheel by SuperSpeed Scooter on Thu, 2022-11-03 19:13 |
2 |
by oangelo Wed, 2023-01-11 12:25 |
General discussion | |
|
RPM increase by Tibor Kalman Za... on Tue, 2021-02-23 10:12 |
2 |
by Tibor Kalman Za... Sat, 2021-02-27 21:41 |
VESC Tool | |
|
FAULT_CODE_DRV by protontim on Fri, 2017-10-06 04:19 |
2 |
by protontim Tue, 2017-10-10 22:34 |
General discussion | |
|
Connect VESC to Keyboard/Wireless Joystick by sanketh1691 on Mon, 2021-10-04 20:58 |
2 |
by sanketh1691 Wed, 2021-10-06 18:58 |
VESC Tool | |
|
Reverse polarity with 12V battery on Vesc 6, now giving fault codes by Kokonenen on Tue, 2023-03-28 13:45 |
2 |
by frank Wed, 2023-03-29 09:56 |
General discussion | |
|
Is there a workaround to set regen voltage, not current? by Gsorter on Sat, 2023-03-11 17:59 |
2 |
by Gsorter Sat, 2023-03-11 23:48 |
General discussion | |
|
Vesc 6 Hardware layout releasing "in the near future" by david_hickox on Wed, 2018-03-07 04:42 |
2 |
by TechAUmNu Wed, 2018-04-04 21:11 |
VESC6 Beta | |
|
4.12 Phase current/voltage sense mix up. Need assistance please. by shaman on Tue, 2019-01-29 14:58 |
2 |
by shaman Tue, 2019-01-29 16:24 |
Third Party Hardware | |
|
Change RPM of motor by Gas_Sn4ke on Wed, 2019-01-16 03:51 |
2 |
by Shaik Siraaj Thu, 2019-01-17 11:14 |
General discussion | |
|
Setting up a VESC 6 MK IV and need 58.2 voltage fault by warrenhdavis on Fri, 2020-05-22 07:34 |
2 |
by TheFallen Wed, 2020-05-27 08:59 |
VESC Original Hardware | |
|
Duty cycle take 95% when motor released by Rarikao on Mon, 2019-12-23 08:57 |
2 |
by agnesnorris Sat, 2020-02-29 03:48 |
VESC Firmware | |
|
Battery to motor voltage by fazekas on Sat, 2021-05-15 16:03 |
2 |
by fazekas Sun, 2021-05-16 20:43 |
General discussion | |
|
Motors in PID control stops responding for a few seconds by rcmower on Tue, 2023-10-10 20:49 |
2 |
by rcmower Thu, 2023-10-12 14:19 |
General discussion | |
|
Hall count drift by xachmo on Mon, 2018-03-26 07:17 |
2 |
by xachmo Wed, 2018-03-28 21:26 |
VESC Original Hardware | |
|
Advanced settings for FOC motor detection (flux linkage) by jaghori.sasan on Sun, 2019-02-17 09:34 |
2 |
by jaghori.sasan Sun, 2019-02-17 17:51 |
VESC Tool | |
|
Sudden motor stop by dmcke5 on Wed, 2018-08-15 13:50 |
2 |
by andreas Thu, 2018-09-06 20:48 |
General discussion | |
|
Writing to slave vesc sometimes cause loss of can bus by meashman on Wed, 2022-07-20 01:08 |
2 |
by frank Thu, 2022-10-27 08:54 |
VESC Tool | |
|
4wd rover using hub-motors by mhyer on Thu, 2023-05-18 09:56 |
2 |
by velolac Tue, 2023-05-23 10:03 |
General discussion |
Pages
