You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
VESC hybrid drone generator by sander123 on Thu, 2024-03-07 10:55 |
1 |
by electricfox Sat, 2024-03-09 19:02 |
General discussion | |
|
Alternator custom VESC hardware: Looking for collaborators by jon@ifold on Wed, 2020-01-15 20:11 |
1 |
by frank Thu, 2020-01-16 16:32 |
General discussion | |
|
Control a 3 phase linear induction motor with vesc by Choocie on Wed, 2020-08-05 14:19 |
1 |
by thefallen Thu, 2020-08-06 23:56 |
General discussion | |
|
motor stops spinning on its own by rsarver on Tue, 2021-03-16 16:30 |
1 |
by rsarver Tue, 2021-03-16 22:13 |
VESC Tool | |
|
How do I field weaken a bldc motor? I don’t see the setting by IPizzaI on Sat, 2024-05-11 18:50 |
by IPizzaI Sat, 2024-05-11 18:50 |
General discussion | ||
|
How to Write Serial Communication Program Not Applicable to RTOS by Jack_Li on Fri, 2019-07-05 06:55 |
by Jack_Li Fri, 2019-07-05 06:58 |
General discussion | ||
|
Repurposed Hyundai Ioniq HSG Hybrid Starter Generator as motor - crunching/cogging by patracy on Sat, 2025-04-12 04:42 |
by patracy Sat, 2025-04-12 04:42 |
General discussion | ||
|
Va, Vb, Vc voltages sampling by masifsr on Sat, 2022-05-14 15:25 |
by masifsr Sat, 2022-05-14 15:25 |
VESC Firmware | ||
|
VESC Express GPS Logging frequency by steveeng on Tue, 2025-03-25 22:55 |
by steveeng Tue, 2025-03-25 22:55 |
General discussion | ||
|
Maximum Motor RPM will not reached by Skyver on Sun, 2022-01-23 10:53 |
by Skyver Sun, 2022-01-23 10:53 |
General discussion | ||
|
High res ABI encoder on Vesc not working by JH on Sun, 2026-01-25 01:23 |
by JH Sun, 2026-01-25 01:23 |
General discussion | ||
|
Help for go-foc m100 whit vesc app tool by Danielg6 on Wed, 2023-07-19 15:52 |
by Danielg6 Wed, 2023-07-19 15:52 |
VESC Tool | ||
|
VESC 6, astroflight 3215, loosing sync with freewheel by Rouckie on Mon, 2020-05-11 00:22 |
by Rouckie Mon, 2020-05-11 00:22 |
VESC Original Hardware | ||
|
Trying to upgrade old Enertion FOCBOX Fw 2.18 by jyl087 on Fri, 2024-09-13 16:26 |
by jyl087 Fri, 2024-09-13 17:31 |
Third Party Hardware | ||
|
Setting PID gains (and other config parameters) over CAN Bus by TheCuriousRobot on Thu, 2022-12-15 22:03 |
by TheCuriousRobot Thu, 2022-12-15 22:03 |
General discussion | ||
|
How to activate e-brake on e-scooter with the throttle by Donatas Sukelis on Sat, 2019-04-27 10:09 |
by Donatas Sukelis Sat, 2019-04-27 10:09 |
VESC Tool | ||
|
Controller (VESC 6 based) dont like small motor by matrixgti on Mon, 2024-01-29 21:27 |
by matrixgti Fri, 2024-02-23 15:37 |
General discussion | ||
|
Flipsky losing its settings by jrowe on Tue, 2019-04-16 00:34 |
by jrowe Tue, 2019-04-16 00:34 |
Third Party Hardware | ||
|
Dutycycle set using uart problem by Raja Sharma on Tue, 2020-07-21 21:38 |
by Raja Sharma Tue, 2020-07-21 21:38 |
VESC Firmware | ||
|
Controlling (HB) Braking from Arduino by Bruce on Sat, 2021-02-27 00:23 |
by Bruce Sat, 2021-02-27 00:23 |
General discussion |
Pages
