You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
PPM Position over CAN bus? by walleywalker » Thu, 2021-12-02 18:47 |
0 |
by walleywalker Thu, 2021-12-02 18:47 |
|
|
ppm customization by alexantosh » Thu, 2021-11-25 18:03 |
0 |
by alexantosh Thu, 2021-12-02 12:21 |
|
|
Vesc 6 MKIV Power Switch by KitemillAS » Wed, 2021-12-01 19:44 |
1 |
by frank Wed, 2021-12-01 22:04 |
|
|
UAVCAN Versus Default VESC CAN Implementation by toma » Thu, 2019-06-13 09:17 |
6 |
by gjesusTec Tue, 2021-11-30 18:50 |
|
|
No DRV8323S faults by peacue » Tue, 2021-11-30 09:09 |
0 |
by peacue Tue, 2021-11-30 09:09 |
|
|
VESC Tool FOC detect success, but no motor running by w0nseok » Sun, 2021-11-28 11:09 |
1 |
by frank Sun, 2021-11-28 20:03 |
|
|
Newbie - controller/motor not working by JLow75 » Tue, 2018-11-13 09:50 |
3 |
by bsissell Fri, 2021-11-26 07:17 |
|
|
PAS 3-wire sensor : possible to check a digital input under VESC-toool? by marc426 » Wed, 2021-10-27 00:26 |
6 |
by velolac Thu, 2021-11-25 20:09 |
|
|
The rpm control is not working properly by ptss37 » Wed, 2021-11-24 03:30 |
0 |
by ptss37 Wed, 2021-11-24 03:44 |
|
|
Can not run again after run perfectly !! Pls help by Streetstar69 » Tue, 2021-11-23 03:03 |
1 |
by frank Tue, 2021-11-23 10:03 |
|
|
vesc tool page not opening by bsissell » Sun, 2021-11-21 20:46 |
1 |
by velolac Sun, 2021-11-21 22:13 |
|
|
Step-by-step manual or overview for VESC + Arduino control by vretier » Sat, 2021-11-20 21:39 |
1 |
by skyline1970 Sun, 2021-11-21 08:33 |
|
|
Two VESCs, two three-phase windings, one motor stator by kubark42 » Fri, 2021-11-12 21:29 |
13 |
by skyline1970 Fri, 2021-11-19 20:05 |
|
|
Unofficial VESC Discord server by kubark42 » Tue, 2021-11-16 16:07 |
0 |
by kubark42 Fri, 2021-11-19 03:12 |
|
|
EDS Files for Somachine or Codesys by philippe faul » Sun, 2021-09-19 18:00 |
1 |
by Tecnoveritas Thu, 2021-11-18 17:06 |
|
|
UART Arduino Monitor by arranto12 » Thu, 2021-11-18 00:24 |
0 |
by arranto12 Thu, 2021-11-18 00:24 |
|
|
Experience with QS120 IPM motor? by marvinrau » Mon, 2021-05-31 14:03 |
12 |
by pe Tue, 2021-11-16 18:20 |
|
|
large hub motors by Frankey » Sat, 2021-11-13 19:35 |
3 |
by spacewalker Tue, 2021-11-16 13:42 |
|
|
Using a cadence sensor or torque sensor as a throttle with a VESC 6 Trampa Boards by UgoLegendre » Tue, 2021-11-16 11:48 |
1 |
by lurch Tue, 2021-11-16 13:02 |
|
|
Braking noisy on Hoverboards hubs . by lurch » Mon, 2021-11-08 15:59 |
2 |
by lurch Mon, 2021-11-15 21:35 |
|
|
ADC control not linear or smooth by arranto12 » Sat, 2021-11-13 23:23 |
4 |
by TechAUmNu Sun, 2021-11-14 01:03 |
|
|
VESC 6+ CAN bus by kimpet » Thu, 2019-04-25 13:40 |
1 |
by eguven Fri, 2021-11-12 20:50 |
|
|
Cannot reach max speed of BLDC motor by rousha42 » Wed, 2021-11-03 20:23 |
4 |
by frank Tue, 2021-11-09 09:46 |
|
|
Encoder disconnection caused shoot through mosfet fire during regen? by devmonkey » Sun, 2021-11-07 18:17 |
2 |
by devmonkey Mon, 2021-11-08 12:21 |
|
|
Controlling BLDC motor with VESC 4.12 and raspberry pi by sanketh1691 » Mon, 2021-11-01 05:36 |
5 |
by sanketh1691 Mon, 2021-11-08 08:27 |
Log in to post new content in the forum.
