You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Knocking inside motor between 10-20km, after and before all is ok by spacewalker » Mon, 2021-05-10 11:00 |
11 |
by Fpvlee Thu, 2021-07-29 15:30 |
|
|
FIRMWARE FPGA by ian67 » Tue, 2021-02-23 17:01 |
1 |
by TheFallen Wed, 2021-07-28 12:08 |
|
|
FOC HFI Voltage by lennyhaacker » Tue, 2021-07-27 04:24 |
0 |
by lennyhaacker Tue, 2021-07-27 04:24 |
|
|
Vesc control over CAN by meilutisr » Thu, 2021-07-22 16:12 |
1 |
by meilutisr Fri, 2021-07-23 18:09 |
|
|
Difference between the current, duty cycle and PID speed control mode by tromes » Thu, 2020-06-11 07:51 |
7 |
by brycej Thu, 2021-07-22 18:49 |
|
|
Stuttering Motor by Pollmann Andreas » Wed, 2021-07-21 23:54 |
0 |
by Pollmann Andreas Wed, 2021-07-21 23:54 |
|
|
Problem with 200A FSESC: Unbalanced Currents by SamuL » Tue, 2021-05-25 20:31 |
6 |
by SamuL Mon, 2021-07-19 10:32 |
|
|
Is this current reading normal? by AliBarrett10 » Sat, 2021-07-17 12:59 |
0 |
by AliBarrett10 Sat, 2021-07-17 12:59 |
|
|
VESC settings to make alternator act as generator by Ruhi » Tue, 2021-07-13 12:29 |
1 |
by vadicus Thu, 2021-07-15 19:38 |
|
|
Can I use 12V power supply? by ryde6 » Sun, 2021-04-25 08:19 |
2 |
by vadicus Wed, 2021-07-14 21:01 |
|
|
ADC Current No Reverse Brake Button / Bluetooth by portnawake » Fri, 2019-05-10 00:35 |
4 |
by Jamalhustle Sun, 2021-07-11 02:14 |
|
|
Arduino and vesc integration issue by dsuresh » Thu, 2021-07-08 17:07 |
1 |
by dsuresh Thu, 2021-07-08 17:09 |
|
|
Motor Saturation Point Measurement by Ebike_Ninja » Fri, 2020-02-28 18:51 |
3 |
by danilolattaro Wed, 2021-07-07 21:35 |
|
|
Driver explosion by fer-bo » Mon, 2021-07-05 11:48 |
4 |
by fer-bo Wed, 2021-07-07 14:50 |
|
|
Can you switch censored to sensor less or HFI by diyRick » Wed, 2021-06-30 23:43 |
2 |
by drdrs Wed, 2021-07-07 07:11 |
|
|
Servo output control by 007trains » Fri, 2021-05-14 15:16 |
3 |
by BalorNG Wed, 2021-06-30 19:42 |
|
|
PAS and Throttle by nguyen victor » Tue, 2021-06-29 14:55 |
0 |
by nguyen victor Tue, 2021-06-29 14:55 |
|
|
Flipsky hall sensors by alanrooks007 » Sat, 2021-06-26 00:55 |
0 |
by alanrooks007 Sat, 2021-06-26 00:55 |
|
|
Flipsky broken off USB ports by mnchvgs79 » Fri, 2021-06-25 20:25 |
0 |
by mnchvgs79 Fri, 2021-06-25 20:25 |
|
|
Input wizard and/or firmware not working for Mini ESC 4.2 with PPM input? by mshipowick » Thu, 2021-06-17 02:08 |
3 |
by mshipowick Thu, 2021-06-24 20:34 |
|
|
Ground Loop question by a.smith » Wed, 2021-06-23 13:25 |
0 |
by a.smith Wed, 2021-06-23 13:25 |
|
|
Max Batt current and max motor current by Inewton » Mon, 2021-06-21 14:43 |
1 |
by spacewalker Tue, 2021-06-22 08:21 |
|
|
*newbie* motors keep running backwards randomly when switch off, and then back on. Embarrassing. by Nikolas Lamshed » Sun, 2021-06-20 13:36 |
0 |
by Nikolas Lamshed Sun, 2021-06-20 13:36 |
|
|
How to control two Can-connected motors separately from microcontroller. by kkkeisuke » Sun, 2021-06-20 06:47 |
0 |
by kkkeisuke Sun, 2021-06-20 12:05 |
|
|
Looking for proper VESC hardware version for E-Scooter Build. 52V by aztecsurf » Thu, 2021-06-17 23:49 |
2 |
by aztecsurf Fri, 2021-06-18 19:04 |
Log in to post new content in the forum.
