You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Flipsky 75100 controller not producing the same amount of power as esc controller at same current by Ashton » Mon, 2021-12-06 21:18 |
2 |
by Liam Li Sun, 2022-03-06 20:31 |
|
|
vesc control with 0-5v analog input... and general motor/esc recomendation by rcjustin » Thu, 2022-03-03 03:33 |
3 |
by j.konrad Fri, 2022-03-04 01:09 |
|
|
VESC100/250; RPM Pulse input; antispark precharge by tobiokanobi » Mon, 2022-02-28 11:56 |
7 |
by tobiokanobi Thu, 2022-03-03 11:22 |
|
|
Best Throttle and break level by ardillolambo » Wed, 2022-03-02 18:29 |
0 |
by ardillolambo Wed, 2022-03-02 18:29 |
|
|
Emergency Stop SSR - Blowing up Microcontroller by J_W97 » Tue, 2022-03-01 14:46 |
5 |
by frank Tue, 2022-03-01 20:19 |
|
|
When SWD Program Connect Fails by canoeman » Mon, 2022-02-28 18:32 |
0 |
by canoeman Mon, 2022-02-28 18:32 |
|
|
Can't receive status message via CAN bus by IanG » Mon, 2020-04-13 03:50 |
4 |
by olivierabristol Sun, 2022-02-27 08:31 |
|
|
Dissimilar motor testing by geofrancis » Thu, 2022-02-24 16:54 |
0 |
by geofrancis Thu, 2022-02-24 16:57 |
|
|
hysteresis related issue in mcconf and mcpwm_foc.c by masifsr » Thu, 2022-02-24 13:14 |
1 |
by j.konrad Thu, 2022-02-24 14:52 |
|
|
VESC for electric scooter by eyup » Tue, 2022-02-22 13:52 |
1 |
by Filip Kinl Thu, 2022-02-24 13:35 |
|
|
Difference between ERPM and Duty Cycle by dormanae » Wed, 2022-02-23 17:21 |
1 |
by j.konrad Thu, 2022-02-24 02:08 |
|
|
Why use sensorless if the motor has sensors? by j.konrad » Thu, 2022-02-17 14:25 |
4 |
by j.konrad Mon, 2022-02-21 15:06 |
|
|
ADC EBike Throttle Not Responding by d_hoody » Thu, 2018-12-13 02:04 |
11 |
by Oded Mazor Sat, 2022-02-19 07:41 |
|
|
will VESC synch with a 1020 inrunner? by Oded Mazor » Fri, 2022-02-18 16:58 |
1 |
by frank Fri, 2022-02-18 17:51 |
|
|
FOC motor just grinds on speed command, spins up smoothly during parameter calibration by mmiles19 » Wed, 2022-02-16 23:21 |
1 |
by frank Thu, 2022-02-17 07:32 |
|
|
Can someone please post the steps to do position control from vesc tool? by dp » Wed, 2022-02-16 14:51 |
1 |
by frank Wed, 2022-02-16 17:24 |
|
|
Motor braking - shorting phases by rok340 » Thu, 2021-01-21 07:49 |
9 |
by dpeinado Mon, 2022-02-14 12:36 |
|
|
VESC won't turn on - RED LED by TKnque » Mon, 2022-02-14 01:01 |
1 |
by frank Mon, 2022-02-14 07:48 |
|
|
Understanding Results from "Experiments" (sweeps) by gazlinux » Thu, 2022-02-10 02:28 |
3 |
by frank Sun, 2022-02-13 11:41 |
|
|
Do I need phase voltage sense? by Flepple » Mon, 2021-01-25 15:31 |
3 |
by GPereira Thu, 2022-02-10 11:43 |
|
|
Updated firmware and remote doesn't work by Africaans » Sat, 2022-01-29 22:18 |
3 |
by jasson Tue, 2022-02-08 09:19 |
|
|
Sending RPM via UART to STM32 by EmirDns » Sat, 2022-01-08 11:00 |
3 |
by EmirDns Mon, 2022-02-07 17:38 |
|
|
CAN eRPM report by alxsfrm » Mon, 2022-02-07 11:01 |
0 |
by alxsfrm Mon, 2022-02-07 11:01 |
|
|
Remote not receiving telemetry data by jasson » Sun, 2022-02-06 04:21 |
2 |
by jasson Sun, 2022-02-06 05:56 |
|
|
Problems with UART communication via Arduino UNO by Michael Hamm » Fri, 2022-02-04 13:29 |
0 |
by Michael Hamm Fri, 2022-02-04 13:29 |
Log in to post new content in the forum.
