You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Measurement of voltage and mah by renaudbarbier » Sun, 2020-05-31 17:04 |
0 |
by renaudbarbier Sun, 2020-05-31 17:04 |
|
|
Set and store Current limit via Canbus by matrixgti » Mon, 2019-08-19 23:13 |
3 |
by Rbz Sun, 2020-05-31 13:44 |
|
|
Do I need a motor with Hall sensor to use Vesc tool? by greew » Sun, 2020-05-31 06:48 |
0 |
by greew Sun, 2020-05-31 06:48 |
|
|
Problem with breaking in use in RC plane by fluffy » Tue, 2020-05-26 06:11 |
3 |
by fluffy Sat, 2020-05-30 03:54 |
|
|
3 shunt low side vs 3 shunt 'in phase' current sensing by ripperpc » Mon, 2020-05-04 08:47 |
6 |
by bww129 Wed, 2020-05-27 17:59 |
|
|
Locking for reconfiguration/reprogramming This topic has been moved to "Feature Requests" (View topic) |
|||
|
Drone application with pixhawk by Kabroc » Tue, 2020-05-12 16:41 |
1 |
by SimpleUnmanned Thu, 2020-05-21 02:46 |
|
|
VESC & Raspberry & Jetson by Andrea » Tue, 2020-05-19 15:58 |
1 |
by SimpleUnmanned Thu, 2020-05-21 02:44 |
|
|
Voltage on motor leads @ 0 throttle by SimpleUnmanned » Thu, 2020-05-21 02:40 |
0 |
by SimpleUnmanned Thu, 2020-05-21 02:40 |
|
|
Factors of VESC motor detection and operation with 3rd Party Hardware by shaman » Wed, 2020-04-01 20:44 |
13 |
by vadicus Wed, 2020-05-13 00:23 |
|
|
9 by RoopeKuisma » Sun, 2020-05-10 21:58 |
0 |
by RoopeKuisma Sun, 2020-05-10 21:58 |
|
|
Getting Started / Prototyping Help by harrym » Wed, 2020-04-01 17:56 |
4 |
by javmarina Sat, 2020-05-09 17:35 |
|
|
(Not) Stator saturation by Stupidspencer » Sun, 2019-10-13 00:34 |
4 |
by bittes Sat, 2020-05-09 14:46 |
|
|
Electric PPG - Light UL plane - ONE motor project by ITGlider » Sat, 2020-05-02 14:55 |
1 |
by mrav Tue, 2020-05-05 11:40 |
|
|
Designing a robust power stage using Mosfets by ripperpc » Tue, 2020-05-05 08:04 |
0 |
by ripperpc Tue, 2020-05-05 08:04 |
|
|
How different of VESC 6 and VESC 4 by Ken_chen » Thu, 2018-05-17 18:13 |
3 |
by ripperpc Mon, 2020-05-04 07:58 |
|
|
How the saliency is affecting the High frequency signal injection? by SOURAV UK » Sun, 2020-05-03 11:35 |
0 |
by SOURAV UK Sun, 2020-05-03 11:35 |
|
|
How I control the RPM of my motor from VESC with Arduino? by George W. » Sat, 2020-04-25 16:10 |
1 |
by frank Thu, 2020-04-30 18:16 |
|
|
program motorstop for VTOL by Jan-Willem » Wed, 2020-04-29 18:55 |
4 |
by frank Thu, 2020-04-30 18:08 |
|
|
VESC/FOC developer needed by CAYAGO_MS » Thu, 2020-04-30 14:23 |
0 |
by CAYAGO_MS Thu, 2020-04-30 14:23 |
|
|
Hoyt Puck Prototipo DSS50+ Firmware questions by tombell » Wed, 2020-04-29 03:56 |
0 |
by tombell Wed, 2020-04-29 03:56 |
|
|
22 pole motor and potentiometer throttle by Kenneth » Mon, 2020-04-27 23:01 |
1 |
by Kenneth Tue, 2020-04-28 08:59 |
|
|
vesc setup 42V 10A e-bike accu to build in a E-skatboard by olaf2273 » Fri, 2020-04-10 12:33 |
0 |
by olaf2273 Mon, 2020-04-27 15:34 |
|
|
How to set dead time on BLDC mode? by AllenFF » Wed, 2020-04-15 03:30 |
0 |
by AllenFF Mon, 2020-04-27 15:34 |
|
|
VESC for EU pedelecs by bb67 » Mon, 2020-04-27 14:11 |
0 |
by bb67 Mon, 2020-04-27 14:13 |
|
Log in to post new content in the forum.
