You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
VESC Mini 4.20 boots up inconsistently, any suggestions by Djmrozinski » Sat, 2021-02-06 10:54 |
1 |
by skyline1970 Sat, 2021-02-06 19:08 |
|
|
Enertion FOCbox question by island bound trading » Sun, 2021-01-31 15:34 |
2 |
by s0313045 Fri, 2021-02-05 03:54 |
|
|
Ayuda español by julitosanse » Wed, 2021-01-27 03:48 |
1 |
by Africaans Wed, 2021-02-03 10:56 |
|
|
can I fit a VESC in my e-skate? by 6diegodiego9 » Thu, 2021-01-21 20:42 |
1 |
by skyline1970 Tue, 2021-02-02 21:30 |
|
|
4.2 hw Erpm bldc mode by Katt » Wed, 2021-01-27 15:48 |
2 |
by Katt Tue, 2021-02-02 14:16 |
|
|
What is the best way to make an emergency button to stop the motor from spinning? by kdomanski » Sat, 2021-01-30 14:18 |
5 |
by skyline1970 Mon, 2021-02-01 21:25 |
|
|
ESK8 by island bound trading » Sat, 2021-01-30 23:16 |
1 |
by island bound trading Sat, 2021-01-30 23:17 |
|
|
Negative current reporting at high erpm in no-load setup by mcdanny » Sun, 2021-01-17 23:04 |
1 |
by moto_guy Sat, 2021-01-30 04:53 |
|
|
Custom Apps on Windows by rok340 » Tue, 2021-01-26 10:05 |
5 |
by rok340 Fri, 2021-01-29 08:33 |
|
|
uart position control by kragon » Sun, 2021-01-24 13:34 |
1 |
by kragon Thu, 2021-01-28 16:46 |
|
|
firmware version by Brian123 » Sat, 2021-01-23 06:48 |
1 |
by Brian123 Sat, 2021-01-23 07:35 |
|
|
is VESC compatible with ROS by Knightfluffy » Fri, 2021-01-15 02:31 |
1 |
by TechAUmNu Sat, 2021-01-16 14:05 |
|
|
HALL-FOC---don't understand the mcpwm_foc_hall_detect() function by ConnerL » Wed, 2021-01-06 12:33 |
2 |
by ConnerL Tue, 2021-01-12 02:55 |
|
|
VESC Hardware Design For 4 in 1 Quadcopter ESC Board? by aklimaj » Wed, 2021-01-06 22:55 |
2 |
by TheFallen Mon, 2021-01-11 08:38 |
|
|
How to reboot VESC from serial port by Ivko » Mon, 2021-01-04 18:45 |
1 |
by rosemery2511 Tue, 2021-01-05 22:41 |
|
|
How to reboot VESC from serial port by Ivko » Mon, 2021-01-04 18:44 |
0 |
by Ivko Mon, 2021-01-04 18:44 |
|
|
AS5047 Encoder with VESC 4.20 by rctestflight » Mon, 2020-09-21 19:55 |
1 |
by aparanjpe Sun, 2021-01-03 17:45 |
|
|
Why not using interrupt for Hall signal detection? by kuan » Sun, 2021-01-03 09:51 |
0 |
by kuan Sun, 2021-01-03 09:51 |
|
|
Ayuda configurar vesc tool by julitosanse » Sat, 2021-01-02 13:24 |
0 |
by julitosanse Sat, 2021-01-02 13:24 |
|
|
Where to find CAN protocol documentation? by doctarr » Tue, 2020-12-29 15:33 |
0 |
by doctarr Tue, 2020-12-29 15:33 |
|
|
Wheel speed over CANBUS by paule » Tue, 2020-12-29 13:04 |
0 |
by paule Tue, 2020-12-29 13:04 |
|
|
FSESC 4.12 oscillating and making noise by hichemhlm » Sun, 2020-03-29 13:33 |
1 |
by hichemhlm Sun, 2020-12-27 12:19 |
|
|
Hall sensors + incremental encoder by SAK-SIVAL » Thu, 2020-10-08 18:37 |
2 |
by tonyXHB Tue, 2020-12-22 13:33 |
|
|
Complete lack of torque on DIY e-bike by Frazatto » Fri, 2020-09-18 21:01 |
6 |
by tonyXHB Tue, 2020-12-22 13:18 |
|
|
Vesc board on ebike by tailele » Sat, 2020-11-14 15:08 |
2 |
by tonyXHB Tue, 2020-12-22 12:21 |
Log in to post new content in the forum.
