You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
throttle programing by turbomullet » Sun, 2021-03-07 22:42 |
0 |
by turbomullet Sun, 2021-03-07 22:42 |
|
|
High speed braking failure by danspratt » Wed, 2020-07-22 23:58 |
11 |
by knuthcomi Sat, 2021-03-06 23:48 |
|
|
Motor moves jerky by dsuresh » Thu, 2021-03-04 19:38 |
2 |
by dsuresh Fri, 2021-03-05 18:17 |
|
|
Problem with motor startup - only 1/2 of pole positions work in FOC by Knapers » Wed, 2021-03-03 16:51 |
0 |
by Knapers Wed, 2021-03-03 17:00 |
|
|
ESC blinks red when I give it input by menghaitang » Tue, 2021-03-02 21:22 |
1 |
by Knapers Wed, 2021-03-03 16:57 |
|
|
Sporadic Duty Cycle by Patrick Donovan » Tue, 2021-03-02 01:34 |
2 |
by Patrick Donovan Tue, 2021-03-02 15:55 |
|
|
ADC1 reads incorrect values by dsuresh » Tue, 2021-02-23 00:51 |
2 |
by dsuresh Mon, 2021-03-01 20:37 |
|
|
FSESC6.6+ Over Voltage Fault 80mm Motors by Yomiel » Fri, 2020-03-20 03:45 |
4 |
by TheFallen Mon, 2021-03-01 16:47 |
|
|
is Cross Coupling power limitation? by ziumus » Sat, 2021-02-06 15:57 |
6 |
by ziumus Sat, 2021-02-27 16:08 |
|
|
Controlling (HB) Braking from Arduino by Bruce » Sat, 2021-02-27 00:23 |
0 |
by Bruce Sat, 2021-02-27 00:23 |
|
|
esc tester by FatsoBatso » Wed, 2021-02-24 18:05 |
1 |
by skyline1970 Fri, 2021-02-26 14:55 |
|
|
Vesc red LED on by dsuresh » Wed, 2021-02-24 18:01 |
0 |
by dsuresh Wed, 2021-02-24 18:01 |
|
|
display readings by FatsoBatso » Wed, 2021-02-24 18:01 |
0 |
by FatsoBatso Wed, 2021-02-24 18:01 |
|
|
as5047d drift?,Vd voltage -10 by ziumus » Sat, 2021-02-20 20:38 |
3 |
by ziumus Tue, 2021-02-23 22:08 |
|
|
anti theft possible? by hummina » Tue, 2021-02-23 07:44 |
0 |
by hummina Tue, 2021-02-23 07:44 |
|
|
VESC on Chromebook? by Boa1277 » Sun, 2021-02-21 20:49 |
0 |
by Boa1277 Sun, 2021-02-21 20:49 |
|
|
Communication with Vesc Tools by faheemift » Tue, 2021-02-09 16:08 |
8 |
by beatrixena Sat, 2021-02-20 09:11 |
|
|
PWM connection for a remote by dsuresh » Fri, 2021-02-19 19:17 |
0 |
by dsuresh Fri, 2021-02-19 19:17 |
|
|
VESC controlled by CAN by j.m » Wed, 2021-02-17 10:51 |
1 |
by TheFallen Fri, 2021-02-19 00:52 |
|
|
how to delete pc install, struggling to get the mobile program to work :) by jon218white » Thu, 2021-02-18 20:47 |
1 |
by TheFallen Fri, 2021-02-19 00:31 |
|
|
Hoverboard motors not spinning when manually controlled, work when doing hall test etc. by VK2EVA » Fri, 2020-12-25 22:01 |
2 |
by ATHIVEL Thu, 2021-02-18 15:45 |
|
|
Using a VESC V4.12 for a machining lathe by Krampas » Sun, 2019-06-09 22:16 |
19 |
by Luke264 Wed, 2021-02-17 18:53 |
|
|
PID Position Controller by IanG » Wed, 2020-03-25 03:05 |
5 |
by Luke264 Wed, 2021-02-17 18:53 |
|
|
Setting PI / PID controllers in VESC for very low speeds. For CNC by K@RLSON » Sat, 2020-01-25 21:06 |
9 |
by Luke264 Wed, 2021-02-17 18:52 |
|
|
UART CAN forwarding by frankus » Tue, 2019-01-29 16:07 |
4 |
by frankus Tue, 2021-02-16 06:35 |
Log in to post new content in the forum.
