You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
VESC is not working in ADC mode by asnamp » Thu, 2022-04-21 06:53 |
2 |
by asnamp Fri, 2022-04-22 06:50 |
|
|
VESC is not working in ADC mode by asnamp » Wed, 2022-04-20 09:21 |
0 |
by asnamp Thu, 2022-04-21 20:11 |
|
|
Multiple VESCs on the same battery by Riccio » Wed, 2022-04-20 22:09 |
0 |
by Riccio Wed, 2022-04-20 22:09 |
|
|
Vesc is not turning on by asnamp » Wed, 2022-04-20 09:30 |
1 |
by canoeman Wed, 2022-04-20 15:44 |
|
|
Autonomous Drifting Research Project by AutonomousDrifting » Fri, 2020-10-30 13:05 |
1 |
by AutonomousDrifting Tue, 2022-04-19 23:21 |
|
|
Motor detection failed by DragosZapodeanu » Tue, 2022-04-19 15:09 |
0 |
by DragosZapodeanu Tue, 2022-04-19 15:09 |
|
|
Where can I ask technical questions about products? by MrSurly » Tue, 2022-04-19 05:22 |
0 |
by MrSurly Tue, 2022-04-19 05:22 |
|
|
Design custom VESC 6 Hardware by brightlightbeam » Sat, 2020-07-04 14:18 |
5 |
by Gatze Mon, 2022-04-18 18:22 |
|
|
Servo output CAN Formats by vinci » Mon, 2022-04-18 15:35 |
0 |
by vinci Mon, 2022-04-18 15:35 |
|
|
Control of 4000w bldc motor with hall effect sensors by Abdullah Ajmal » Sat, 2022-04-16 10:14 |
1 |
by frank Sat, 2022-04-16 20:01 |
|
|
Your input needed: FESC 4.12 / Arduino / 4X 350W motors by matukash » Tue, 2020-07-21 16:36 |
6 |
by frank Fri, 2022-04-15 17:31 |
|
|
Hybrid mode in FOC - possible? by Oded Mazor » Tue, 2022-04-12 07:42 |
4 |
by Oded Mazor Wed, 2022-04-13 11:28 |
|
|
Flux linkage detection failed by Count1310 » Sat, 2020-08-22 16:30 |
3 |
by drummerboy5408 Wed, 2022-04-13 07:42 |
|
|
Motor compatibility (and power levels) by MrSurly » Tue, 2022-04-12 21:43 |
0 |
by MrSurly Tue, 2022-04-12 21:43 |
|
|
Flipsky 75/100 Mosfet short? by Michael Campbell » Mon, 2022-04-11 08:29 |
4 |
by Michael Campbell Tue, 2022-04-12 00:03 |
|
|
Pid_Speed is braking despite no brake option by Flyingtux » Thu, 2022-04-07 09:41 |
2 |
by Flyingtux Thu, 2022-04-07 15:49 |
|
|
Burned my VESC 6 MKV. Wrong polarity by okhsunrog » Thu, 2022-04-07 01:44 |
4 |
by frank Thu, 2022-04-07 10:27 |
|
|
AMT 102 Encoder not working properly with VESC by DerpRush » Thu, 2019-07-25 11:32 |
5 |
by ripperpc Wed, 2022-04-06 21:36 |
|
|
Using UART from LabVIEW by hannnes » Tue, 2022-04-05 15:19 |
0 |
by hannnes Tue, 2022-04-05 15:19 |
|
|
Adjusting Acceleration Ramp with NRF & Current control by Mido » Tue, 2022-04-05 14:36 |
0 |
by Mido Tue, 2022-04-05 14:36 |
|
|
Corrupted firmware by Phill Dixon » Mon, 2022-04-04 08:27 |
2 |
by Phill Dixon Mon, 2022-04-04 10:50 |
|
|
VESC usefull for high speed regeneration? by Riccio » Fri, 2022-03-11 10:45 |
5 |
by Riccio Sat, 2022-04-02 11:21 |
|
|
Set RPM - reverse direction over CAN-Bus by 65273 » Tue, 2022-03-29 14:49 |
4 |
by 65273 Fri, 2022-04-01 15:53 |
|
|
Vesc 100/250 (Trampa board) wiring for ebike by Oded Mazor » Fri, 2022-03-18 23:34 |
8 |
by Markula Fri, 2022-04-01 09:21 |
|
|
PWM on output by ml2311 » Tue, 2021-08-24 14:46 |
5 |
by Flyingtux Wed, 2022-03-30 19:31 |
Log in to post new content in the forum.
