You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Motor Saturation Point Measurement by Ebike_Ninja » Fri, 2020-02-28 18:51 |
3 |
by danilolattaro Wed, 2021-07-07 21:35 |
|
Driver explosion by fer-bo » Mon, 2021-07-05 11:48 |
4 |
by fer-bo Wed, 2021-07-07 14:50 |
|
Can you switch censored to sensor less or HFI by diyRick » Wed, 2021-06-30 23:43 |
2 |
by drdrs Wed, 2021-07-07 07:11 |
|
Servo output control by 007trains » Fri, 2021-05-14 15:16 |
3 |
by BalorNG Wed, 2021-06-30 19:42 |
|
PAS and Throttle by nguyen victor » Tue, 2021-06-29 14:55 |
0 |
by nguyen victor Tue, 2021-06-29 14:55 |
|
Flipsky hall sensors by alanrooks007 » Sat, 2021-06-26 00:55 |
0 |
by alanrooks007 Sat, 2021-06-26 00:55 |
|
Flipsky broken off USB ports by mnchvgs79 » Fri, 2021-06-25 20:25 |
0 |
by mnchvgs79 Fri, 2021-06-25 20:25 |
|
Input wizard and/or firmware not working for Mini ESC 4.2 with PPM input? by mshipowick » Thu, 2021-06-17 02:08 |
3 |
by mshipowick Thu, 2021-06-24 20:34 |
|
Ground Loop question by a.smith » Wed, 2021-06-23 13:25 |
0 |
by a.smith Wed, 2021-06-23 13:25 |
|
Max Batt current and max motor current by Inewton » Mon, 2021-06-21 14:43 |
1 |
by spacewalker Tue, 2021-06-22 08:21 |
|
*newbie* motors keep running backwards randomly when switch off, and then back on. Embarrassing. by Nikolas Lamshed » Sun, 2021-06-20 13:36 |
0 |
by Nikolas Lamshed Sun, 2021-06-20 13:36 |
|
How to control two Can-connected motors separately from microcontroller. by kkkeisuke » Sun, 2021-06-20 06:47 |
0 |
by kkkeisuke Sun, 2021-06-20 12:05 |
|
Looking for proper VESC hardware version for E-Scooter Build. 52V by aztecsurf » Thu, 2021-06-17 23:49 |
2 |
by aztecsurf Fri, 2021-06-18 19:04 |
|
Problem with motor spin in Foc with encoder mode by kdomanski » Thu, 2021-06-17 21:55 |
1 |
by kdomanski Fri, 2021-06-18 15:28 |
|
How can I add watts data to solidgeek? by Fixitmoditbreakit » Sat, 2021-06-12 00:07 |
2 |
by vadicus Tue, 2021-06-15 17:50 |
|
Flipsky motor setup by Rengineer » Tue, 2021-06-15 14:03 |
0 |
by Rengineer Tue, 2021-06-15 14:03 |
|
Sensorless tuning tips on bicycle hub motor by kalvdans » Sat, 2021-06-12 11:51 |
2 |
by neo Tue, 2021-06-15 02:02 |
|
Question about UARTs by melluh » Sun, 2021-06-13 22:50 |
1 |
by vadicus Mon, 2021-06-14 01:15 |
|
Motor stuttering at full throttle by de-bodgery » Wed, 2021-06-09 01:22 |
3 |
by frank Fri, 2021-06-11 20:48 |
|
VSEC firmware update issue by dsuresh » Thu, 2021-02-11 17:25 |
8 |
by Macc Fri, 2021-06-11 13:10 |
|
Differential steering setup by GCTech » Sat, 2020-07-04 17:38 |
3 |
by TheFallen Fri, 2021-06-11 09:36 |
|
Send battery voltage as a serial signal to Arduino? by Wall_Nut_ » Sun, 2021-06-06 15:18 |
2 |
by Wall_Nut_ Thu, 2021-06-10 12:09 |
|
VESC for BLDC Pump- motor settings by ar5000 » Thu, 2021-06-10 10:02 |
6 |
by frank Thu, 2021-06-10 11:42 |
|
Dual Motor Software "Limited Slip" Differential by luky » Thu, 2021-06-10 10:43 |
1 |
by frank Thu, 2021-06-10 11:07 |
|
Arduino UART max Current and max RPM setting by h2omatt » Wed, 2020-09-30 23:49 |
5 |
by dsuresh Tue, 2021-06-08 20:59 |
Log in to post new content in the forum.