You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
How to Create Resistance Using a BLDC Motor for a Stationary Bike Conversion? by Prayoga » Tue, 2025-07-01 01:23 |
5 |
by Prayoga Mon, 2025-07-21 14:58 |
|
|
Kaabo mantis 10 elite(minimotors) FLIPSJY 75100 DUAL ALU PCB by Musik117 » Fri, 2025-07-18 14:33 |
0 |
by Musik117 Fri, 2025-07-18 14:33 |
|
|
VESC Replacing Shunt Resistor with Hall Current Sensor？ by happy85 » Fri, 2025-07-18 06:21 |
0 |
by happy85 Fri, 2025-07-18 11:51 |
|
|
Could use some help tuning for low speed by Berrie » Tue, 2025-07-15 20:24 |
0 |
by Berrie Tue, 2025-07-15 20:24 |
|
|
Question about UARTs by melluh » Sun, 2021-06-13 22:50 |
2 |
by Rc 44 Fri, 2025-07-11 22:04 |
|
|
Arduino and vesc integration issue by dsuresh » Thu, 2021-07-08 17:07 |
2 |
by Rc 44 Fri, 2025-07-11 21:57 |
|
|
Vesc antispark always active by axelSSS » Wed, 2025-06-18 19:44 |
1 |
by tokerodev Fri, 2025-07-04 21:47 |
|
|
Repairing by lamak » Thu, 2025-06-26 07:08 |
2 |
by ispor4en Fri, 2025-06-27 21:15 |
|
|
eRPM limited to 40600 or so on 6.6 by Dan Slanker » Fri, 2021-04-16 01:22 |
6 |
by electricfox Wed, 2025-06-18 10:11 |
|
|
Switch between pre-defined profiles over UART by PutridFox » Sun, 2025-06-15 13:11 |
0 |
by PutridFox Sun, 2025-06-15 13:11 |
|
|
Looking for VESC Tuning Help will pay $ by jordan73s » Sun, 2025-05-04 02:23 |
2 |
by colmor Thu, 2025-06-12 21:35 |
|
|
IMU 9250 and 6050 not working on new vesc 4.12 and 4.20 by trung_qly » Sun, 2021-09-05 16:11 |
3 |
by spatsirk Mon, 2025-06-09 18:55 |
|
|
Using the parameter editor by dqt boi » Thu, 2019-10-24 23:31 |
1 |
by Anuj Sat, 2025-06-07 16:23 |
|
|
base on VESC6_MkVI by gavin » Wed, 2025-06-04 15:48 |
0 |
by gavin Wed, 2025-06-04 15:48 |
|
|
vesc tool by gavin » Wed, 2025-06-04 15:30 |
1 |
by gavin Wed, 2025-06-04 15:31 |
|
|
Flipsky and Trampa getting two very different detected resistances on same motor! by colmor » Wed, 2025-05-28 22:52 |
0 |
by colmor Wed, 2025-05-28 22:52 |
|
|
Trouble with Sensorless Startup on Trampa 6376 160Kv Motors (VESC 6 Dual, FW 6.05) by bojfik » Mon, 2025-05-26 14:35 |
1 |
by bojfik Tue, 2025-05-27 15:51 |
|
|
Reversed polarity on one of my controllers when setting up by jsherbz92 » Sun, 2025-05-25 15:16 |
0 |
by jsherbz92 Sun, 2025-05-25 15:16 |
|
|
Cruise control by palaga » Tue, 2025-05-20 09:20 |
0 |
by palaga Tue, 2025-05-20 09:20 |
|
|
vesc 75100 variations for a kart build by elbracer » Mon, 2025-05-19 19:57 |
0 |
by elbracer Mon, 2025-05-19 19:57 |
|
|
Pole Pairs by donrecardo » Fri, 2020-06-05 10:24 |
4 |
by Bgbalz75 Fri, 2025-05-16 13:01 |
|
|
Obarter D5 settings for FSESC75100 by wuzamarine » Sun, 2025-05-11 01:23 |
1 |
by wuzamarine Wed, 2025-05-14 16:23 |
|
|
Query: Can I run my 70-pole motor using a VESC-based Flipskey controller? by avaid » Thu, 2025-05-08 12:57 |
0 |
by avaid Tue, 2025-05-13 08:02 |
|
|
Motor seize and ERPM current ramp speed by krabsheva » Tue, 2025-05-13 06:49 |
0 |
by krabsheva Tue, 2025-05-13 07:00 |
|
|
Vesc 4.12 USB Issues by puravida13 » Tue, 2025-05-06 18:45 |
1 |
by puravida13 Sat, 2025-05-10 01:53 |
Log in to post new content in the forum.
