You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
MakerX-FOC DV6s PWM for 2 BLDC Motors by paulsimpsonii » Tue, 2026-03-03 18:08 |
0 |
by paulsimpsonii Tue, 2026-03-03 18:08 |
|
|
Flipsky 75100 pro v2 ADC throttle stopped responding by JozoBozo » Tue, 2026-02-24 17:33 |
2 |
by JozoBozo Sun, 2026-03-01 13:40 |
|
|
Flipsky 72150 outboard cannot connect via USB by EddieEagle1970 » Sat, 2026-02-21 16:56 |
2 |
by mariuszdymon Sat, 2026-02-28 23:37 |
|
|
KERS system with a VESC 100/250 MKIII by Simone Succi » Thu, 2026-02-26 08:28 |
0 |
by Simone Succi Thu, 2026-02-26 16:20 |
|
|
Set current - is it input or phase current? by aegidius » Sun, 2026-02-08 05:58 |
0 |
by aegidius Sun, 2026-02-08 05:58 |
|
|
Motor detection and calibration using CAN by charan » Tue, 2026-02-03 14:48 |
0 |
by charan Tue, 2026-02-03 14:48 |
|
|
High res ABI encoder on Vesc not working by JH » Sun, 2026-01-25 01:23 |
0 |
by JH Sun, 2026-01-25 01:23 |
|
|
Question about duty cycle control Vs current control mode by hazzahodgson » Wed, 2026-01-21 08:34 |
0 |
by hazzahodgson Wed, 2026-01-21 08:34 |
|
|
ESP-NOW Remote control by brightlightbeam » Sun, 2026-01-18 12:00 |
1 |
by A-damW Wed, 2026-01-21 04:28 |
|
|
Issue connecting to Flipsky VESC with mobile app (Firmware 6.0.6) by Gabifat » Mon, 2025-12-15 08:35 |
0 |
by Gabifat Mon, 2025-12-15 08:35 |
|
|
tuning low kv high pole sensorless outrunner by cdlapoin » Tue, 2025-05-20 22:14 |
3 |
by flagoworld Wed, 2025-12-10 19:29 |
|
|
Motor "sticks" and stops spinning by flagoworld » Fri, 2025-12-05 19:03 |
0 |
by flagoworld Fri, 2025-12-05 19:03 |
|
|
Running motors under 900ERPM in speed control by Chieflouis01 » Thu, 2025-11-27 21:32 |
2 |
by Chieflouis01 Thu, 2025-11-27 21:33 |
|
|
Motor stopped and I had to run Setup Motors FOC wizard to get it going again by JasonBear » Fri, 2025-11-14 13:24 |
2 |
by JasonBear Sun, 2025-11-16 20:41 |
|
|
FOC detection. by Roger Wolff » Tue, 2025-10-21 19:57 |
1 |
by tobiokanobi Sat, 2025-11-15 21:02 |
|
|
Vesc Orientation Python by flomai28 » Mon, 2025-11-10 09:44 |
0 |
by flomai28 Mon, 2025-11-10 09:44 |
|
|
wont gonnect by rustman01 » Wed, 2025-11-05 19:26 |
0 |
by rustman01 Wed, 2025-11-05 19:26 |
|
|
VESC to spin motor after power up? by A_Baum92881 » Fri, 2025-10-31 06:01 |
0 |
by A_Baum92881 Fri, 2025-10-31 17:21 |
|
|
PAS with variable assist+regen brake by Lukas_T » Fri, 2025-08-29 18:05 |
2 |
by Lukas_T Fri, 2025-10-31 10:28 |
|
|
Vesc boost charging with external inductors by Bunda » Wed, 2025-10-29 08:37 |
0 |
by Bunda Wed, 2025-10-29 08:38 |
|
|
vesctool 6.06 for Mac? by gregd72002 » Sat, 2025-09-27 03:36 |
3 |
by electricfox Sat, 2025-10-25 21:34 |
|
|
Hall sensor port repeatedly fried on original hardware by Rc 44 » Fri, 2025-10-24 22:44 |
0 |
by Rc 44 Fri, 2025-10-24 22:44 |
|
|
Issues with throttle range translating to duty by Elliot Kingsley » Thu, 2025-10-16 02:40 |
1 |
by cwk1234 Tue, 2025-10-21 02:22 |
|
|
Charging Li-ion battery using the VESC Harmony 32S BMS by sainihalj » Tue, 2025-10-14 14:42 |
0 |
by sainihalj Tue, 2025-10-14 14:42 |
|
|
About How to control the "FLIPSKY Dual FSESC6.7 PLUS" by tonyH » Tue, 2025-10-14 11:35 |
0 |
by tonyH Tue, 2025-10-14 11:35 |
Log in to post new content in the forum.
