You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
VESC 100/250 Voltage spikes? by LondonNight » Mon, 2022-09-05 08:21 |
2 |
by LondonNight Fri, 2022-09-09 18:01 |
|
|
Current limit problem by albheim » Fri, 2022-09-09 10:34 |
2 |
by albheim Fri, 2022-09-09 13:24 |
|
|
Reverse rotation command during forward rotation by nisigundam » Wed, 2018-03-07 09:12 |
5 |
by Josh54 Thu, 2022-09-08 18:08 |
|
|
Motor parameters constantly changing. by Alistair Goodman » Tue, 2022-09-06 15:57 |
1 |
by Alistair Goodman Wed, 2022-09-07 10:04 |
|
|
FSESC 4.20 Tuning for RC ESC? by Abcc123 » Thu, 2022-09-01 04:41 |
4 |
by Abcc123 Wed, 2022-09-07 00:23 |
|
|
Are all VESC based ESCs within the same generation standardized in their sensors and data payloads? by pearlgreymusic » Sat, 2022-08-27 11:43 |
2 |
by pearlgreymusic Tue, 2022-09-06 14:24 |
|
|
Encoder maximum PPR/CPR by Michelle90 » Mon, 2022-09-05 22:16 |
0 |
by Michelle90 Mon, 2022-09-05 22:16 |
|
|
Weird Inductance measurement by a.dahhak » Wed, 2020-06-03 21:53 |
6 |
by Gatze Mon, 2022-09-05 20:07 |
|
|
VESC 6 EDU: Motor Wizard - Detection failed by Navigator_PJE » Mon, 2022-08-29 16:12 |
0 |
by Navigator_PJE Mon, 2022-08-29 16:12 |
|
|
FOC and very low speeds by verbeek » Mon, 2018-07-09 16:17 |
10 |
by moose09876 Wed, 2022-08-24 20:05 |
|
|
Dual motor for a small boat by Snabelost » Wed, 2022-08-24 10:58 |
1 |
by Snabelost Wed, 2022-08-24 13:56 |
|
|
VESCs rotating the motors at constant RPM on UART control by Pratham701 » Tue, 2021-07-13 10:49 |
1 |
by Indy8976 Wed, 2022-08-24 11:27 |
|
|
vesc tool motor help! by Gr8adventures » Fri, 2022-08-19 21:48 |
2 |
by Gr8adventures Tue, 2022-08-23 13:10 |
|
|
Is there a VESC with the form factor like a Votol EM200 ? (with those threaded lugs|Screw Terminals)) by Gatze » Sat, 2022-03-12 09:33 |
8 |
by qdxiatao Sat, 2022-08-20 04:09 |
|
|
IPM/Salient Motor Tuning by SRFirefox » Wed, 2020-08-26 23:19 |
2 |
by JP Wed, 2022-08-17 11:22 |
|
|
Spam (Page: 1, 2)
by Davideo » Mon, 2017-12-25 20:49 |
81 |
by canoeman Tue, 2022-08-16 15:19 |
|
|
Small inrunner HFI set-up issue by anthony_ » Thu, 2022-08-11 13:43 |
2 |
by anthony_ Mon, 2022-08-15 13:45 |
|
|
In FOC mode, MOSFET is often burned out! In BLDC mode, normal! by return97 » Sat, 2022-07-23 17:31 |
4 |
by return97 Sun, 2022-08-14 16:53 |
|
|
Vesc 100/250 for unsensored brushless motors by jmurba » Fri, 2022-08-05 12:05 |
3 |
by velolac Fri, 2022-08-12 22:14 |
|
|
Starter motor stoping for no apparent reason by Bexy » Wed, 2022-08-03 18:07 |
2 |
by jiushiwo Thu, 2022-08-11 08:23 |
|
|
step/dir by blueflower » Thu, 2020-01-16 04:15 |
5 |
by akkoxe Mon, 2022-08-08 06:34 |
|
|
Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM by PaulMakesThings » Fri, 2022-08-05 11:06 |
0 |
by PaulMakesThings Fri, 2022-08-05 11:06 |
|
|
Updated VESC 6 schematic request by ma-j-sterelektron » Mon, 2019-03-25 08:43 |
3 |
by Roby_88 Thu, 2022-08-04 12:43 |
|
|
temperature compensation make sense？ by alexshen2012 » Thu, 2022-08-04 08:28 |
1 |
by alexshen2012 Thu, 2022-08-04 09:17 |
|
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset » Thu, 2022-08-04 01:44 |
0 |
by liminalsunset Thu, 2022-08-04 01:44 |
Log in to post new content in the forum.
