You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Porting vesc to this closed source controller? by st0r » Sat, 2023-01-28 19:07 |
2 |
by jaykup Tue, 2023-01-31 03:05 |
|
|
PAS function by sam.vanratt » Sat, 2018-11-24 14:53 |
5 |
by Oldbike2011 Mon, 2023-01-30 06:05 |
|
|
Any way to increase detection time? by VapeGod » Wed, 2023-01-25 05:58 |
0 |
by VapeGod Wed, 2023-01-25 05:58 |
|
|
VESC shutdown while accelerating by fpfeifer » Sat, 2023-01-21 23:42 |
2 |
by vadicus Wed, 2023-01-25 02:25 |
|
|
Activate second UART port by daltonthomas » Sat, 2021-11-13 10:10 |
2 |
by Maser Sat, 2023-01-21 07:37 |
|
|
100V/250A Vesc for sale!!!!! by Fpvlee » Mon, 2021-11-08 03:59 |
2 |
by Svein Utne Fri, 2023-01-20 08:56 |
|
|
What do the LEDs mean? by Chaim Lukas Maier » Thu, 2023-01-19 16:35 |
1 |
by frank Thu, 2023-01-19 18:02 |
|
|
Multiple VESCs, CANBus, Galvanic Isolation and Puffs of Smoke by KirkusMaximus » Wed, 2023-01-18 00:55 |
1 |
by frank Wed, 2023-01-18 12:29 |
|
|
Questions about encoder on FSesc 6 by willyfan » Wed, 2018-08-29 20:30 |
11 |
by Vedderfanboy Tue, 2023-01-17 13:17 |
|
|
5.02 Firmware on Trampa VESC 6 MKVI? by maxhertz » Sun, 2023-01-15 13:58 |
2 |
by maxhertz Mon, 2023-01-16 00:24 |
|
|
Brake lever Cutoff switch seperate from Regen braking/throttle wheel by SuperSpeed Scooter » Thu, 2022-11-03 19:13 |
2 |
by oangelo Wed, 2023-01-11 12:25 |
|
|
Fault Code Look Up Table (for CSV, Excel or Similar) by JayCee » Wed, 2023-01-11 04:26 |
0 |
by JayCee Wed, 2023-01-11 04:26 |
|
|
motors wont turn by Jambi56 » Mon, 2022-09-26 01:48 |
2 |
by Zander rowley Mon, 2023-01-09 16:43 |
|
|
Bldc generator voltage control by Gsorter » Fri, 2022-12-09 23:52 |
3 |
by frank Wed, 2023-01-04 18:39 |
|
|
Help i have no idea how it works... by Xtracker133 » Sat, 2022-12-31 14:55 |
2 |
by Xtracker133 Tue, 2023-01-03 22:52 |
|
|
Recommended method for CAN Bus communication for 3 VESC by sivanhere » Sun, 2023-01-01 12:09 |
0 |
by sivanhere Sun, 2023-01-01 12:09 |
|
|
How to implement a simple autopilot by oangelo » Thu, 2022-12-22 12:50 |
0 |
by oangelo Thu, 2022-12-22 12:50 |
|
|
Need help with brushed fc 24 bolt motor control by searth » Sun, 2022-12-18 16:05 |
0 |
by searth Sun, 2022-12-18 16:05 |
|
|
Field weakening and MTPA by Gsorter » Fri, 2022-12-16 21:54 |
2 |
by Gsorter Sun, 2022-12-18 02:20 |
|
|
Impact of motor resistance value vs temperature by Torbjorn » Fri, 2022-12-16 09:09 |
0 |
by Torbjorn Fri, 2022-12-16 09:09 |
|
|
Dangerous bug when using KILLSWITCH and PPM, FW5.03 by corgon » Wed, 2022-12-14 16:37 |
2 |
by corgon Thu, 2022-12-15 23:10 |
|
|
Setting PID gains (and other config parameters) over CAN Bus by TheCuriousRobot » Thu, 2022-12-15 22:03 |
0 |
by TheCuriousRobot Thu, 2022-12-15 22:03 |
|
|
Powering VESC and motor from powersupply by SIGURD » Tue, 2022-12-13 13:53 |
3 |
by frank Thu, 2022-12-15 20:34 |
|
|
VESC and T500 Thruster - Problems obtaining right speed by SIGURD » Tue, 2022-12-13 13:45 |
2 |
by SIGURD Wed, 2022-12-14 16:20 |
|
|
How to avoid engine overheating? by oangelo » Thu, 2022-12-08 23:03 |
3 |
by vadicus Tue, 2022-12-13 22:39 |
Log in to post new content in the forum.
