You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies |
Last post![]() |
|
---|---|---|---|
Setting PID gains (and other config parameters) over CAN Bus by TheCuriousRobot » Thu, 2022-12-15 22:03 |
0 |
by TheCuriousRobot Thu, 2022-12-15 22:03 |
|
Powering VESC and motor from powersupply by SIGURD » Tue, 2022-12-13 13:53 |
3 |
by frank Thu, 2022-12-15 20:34 |
|
VESC and T500 Thruster - Problems obtaining right speed by SIGURD » Tue, 2022-12-13 13:45 |
2 |
by SIGURD Wed, 2022-12-14 16:20 |
|
How to avoid engine overheating? by oangelo » Thu, 2022-12-08 23:03 |
3 |
by vadicus Tue, 2022-12-13 22:39 |
|
Connection issues using PyVESC by axelray » Tue, 2022-12-13 15:15 |
0 |
by axelray Tue, 2022-12-13 15:15 |
|
Help needed please by Mark griffin » Tue, 2022-12-13 14:51 |
0 |
by Mark griffin Tue, 2022-12-13 14:51 |
|
Balancing Throttle by kstuck » Mon, 2022-12-12 22:31 |
1 |
by frank Tue, 2022-12-13 10:37 |
|
Kill Function - Analogue Input by austrobots » Sat, 2022-12-10 12:19 |
5 |
by austrobots Tue, 2022-12-13 04:51 |
|
75/250 question/issue by Petre Daniel Stroe » Sat, 2022-12-10 14:51 |
1 |
by frank Sat, 2022-12-10 21:13 |
|
Why is my VESC Speed (in MPH) half what it should be? by ALarabie » Fri, 2022-12-09 17:41 |
6 |
by vadicus Sat, 2022-12-10 19:00 |
|
impossible to post new feature request by player107 » Wed, 2022-12-07 08:15 |
3 |
by frank Fri, 2022-12-09 14:28 |
|
VESC Logo by beachbrojoe » Thu, 2022-12-08 19:37 |
1 |
by frank Fri, 2022-12-09 14:24 |
|
Power cutoff without any warning by TylerWilson » Fri, 2022-12-09 06:37 |
0 |
by TylerWilson Fri, 2022-12-09 07:11 |
|
Front hub motor on an X11 citycoco fat tire electric trike. by oangelo » Thu, 2022-12-08 22:57 |
0 |
by oangelo Thu, 2022-12-08 22:57 |
|
Motor Jerks and Cogs and gets Very hot by Robert Thomas » Sun, 2022-09-18 00:40 |
2 |
by Snabelost Thu, 2022-12-08 15:45 |
|
Completely disabling regen current possibility on vesc by riraheta » Tue, 2022-11-29 01:48 |
3 |
by frank Wed, 2022-11-30 09:33 |
|
help - vesc tool configure for edf turbine D3541 1450KV 6s DoBoFo by Everton C » Tue, 2022-11-29 15:45 |
1 |
by frank Tue, 2022-11-29 17:52 |
|
drill batteries in series with Flipsky 75100 by alexkid » Sat, 2022-05-14 15:41 |
1 |
by skyline1970 Thu, 2022-11-24 21:41 |
|
SETUP FOR SINGLE BRUSHED MOTOR by mmatthews@aquav... » Fri, 2022-05-13 01:57 |
1 |
by skyline1970 Thu, 2022-11-24 21:39 |
|
Can't start a sensorless motor of a scooter by tobe81cwb » Mon, 2022-05-02 03:25 |
1 |
by skyline1970 Thu, 2022-11-24 21:36 |
|
Controller voor BLDC motor by Kapitein Nelson » Fri, 2022-04-29 17:26 |
1 |
by skyline1970 Thu, 2022-11-24 21:31 |
|
FSESC 75100 repair by BDJ » Fri, 2022-06-24 21:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:22 |
|
VESC as voltage regulator in hybrid UAV by Bunda » Sun, 2022-07-10 08:01 |
1 |
by skyline1970 Thu, 2022-11-24 21:19 |
|
Fault code sensor 1 by krille » Sat, 2022-07-23 16:31 |
1 |
by skyline1970 Thu, 2022-11-24 21:08 |
|
Hall effect sensor type for Flipsky 4.20 by braydinjones » Sun, 2022-07-24 01:06 |
1 |
by skyline1970 Thu, 2022-11-24 21:06 |
Log in to post new content in the forum.
