You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Autodetection values way off by thewho » Sat, 2019-05-25 20:34 |
28 |
by vadicus Mon, 2023-06-19 20:22 |
|
|
Problem cruise with Adaptor 2 by Dominator2 » Sun, 2023-06-18 10:43 |
1 |
by Dominator2 Sun, 2023-06-18 14:55 |
|
|
RPM and torque control modes by srinath » Fri, 2023-06-16 10:52 |
0 |
by srinath Fri, 2023-06-16 10:54 |
|
|
Can bus and Arduino by Snabelost » Wed, 2023-06-14 10:30 |
2 |
by Snabelost Thu, 2023-06-15 08:37 |
|
|
Vesc 75100 by Matteo Christian » Wed, 2023-05-31 13:32 |
0 |
by Matteo Christian Fri, 2023-06-09 12:08 |
|
|
vesc for autonomous robots by _saeed_arabi_ » Tue, 2019-10-15 00:25 |
2 |
by Mayank Wed, 2023-06-07 00:05 |
|
|
No load FOC stops when full FWD throttle. by toboli » Mon, 2023-06-05 18:41 |
0 |
by toboli Mon, 2023-06-05 18:41 |
|
|
Sensorless ERPM confusion and cogging in FOC by Addy » Mon, 2018-05-14 22:38 |
7 |
by bayetan Sun, 2023-06-04 17:19 |
|
|
VESC appears to loose sync when increasing throttle by srinath » Sun, 2023-06-04 04:11 |
0 |
by srinath Sun, 2023-06-04 04:11 |
|
|
Bluemind 80V/450A and 100V/550A by qdxiatao » Fri, 2023-06-02 11:14 |
0 |
by qdxiatao Fri, 2023-06-02 11:14 |
|
|
How can I make status packet, using arduino? by Medist » Thu, 2023-06-01 07:33 |
2 |
by toboli Thu, 2023-06-01 23:06 |
|
|
Progetto Vesc by Matteo Christian » Tue, 2023-05-30 09:20 |
1 |
by frank Wed, 2023-05-31 11:30 |
|
|
Problem with ADC, with no input voltage is 2.6-3.3 by komar » Fri, 2023-05-26 13:59 |
1 |
by dpeinado Wed, 2023-05-31 09:55 |
|
|
Sudden drop in speed after releasing throttle in FW mode by shokrabi » Sat, 2022-04-23 15:05 |
4 |
by DeuceDos Tue, 2023-05-30 09:54 |
|
|
Help Please 🥺 by Jou2023 » Sun, 2023-05-28 17:58 |
0 |
by Jou2023 Sun, 2023-05-28 17:58 |
|
|
VESC Not Functioning with Magnetic or Quadrature Encoders by privvyledge » Wed, 2023-05-24 16:59 |
1 |
by electricfox Thu, 2023-05-25 21:10 |
|
|
Alternate for STM32F405 Microcontroller by gowrav » Fri, 2021-06-18 07:44 |
6 |
by damien31 Wed, 2023-05-24 13:01 |
|
|
Cogging issue with ADC input by Mitsuru Fujii » Mon, 2023-05-22 14:45 |
1 |
by frank Tue, 2023-05-23 16:43 |
|
|
4wd rover using hub-motors by mhyer » Thu, 2023-05-18 09:56 |
2 |
by velolac Tue, 2023-05-23 10:03 |
|
|
3 speed switch by de-bodgery » Sat, 2021-08-21 02:22 |
17 |
by Oscar Lozano Gimenez Mon, 2023-05-22 14:07 |
|
|
static torque control by wjpremerlani » Sun, 2023-05-14 13:52 |
4 |
by wjpremerlani Sat, 2023-05-20 12:23 |
|
|
Motor is "pumping" under load in current control mode. is this normal? by etienne » Sat, 2023-05-13 17:16 |
2 |
by iv.kravchenko Sat, 2023-05-20 08:31 |
|
|
VESC 100/250 missing hall sensor plug by steve1428 » Sat, 2023-04-08 10:00 |
1 |
by iv.kravchenko Fri, 2023-05-19 22:26 |
|
|
vesc app (iphone) brushed motor setting. by outrunner » Tue, 2023-05-16 22:49 |
1 |
by outrunner Wed, 2023-05-17 00:28 |
|
|
Configuration via CAN? by mrPalomar » Tue, 2023-05-16 02:22 |
0 |
by mrPalomar Tue, 2023-05-16 02:22 |
Log in to post new content in the forum.
