You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Burned my VESC 6 MKV. Wrong polarity by okhsunrog » Thu, 2022-04-07 01:44 |
4 |
by frank Thu, 2022-04-07 10:27 |
|
|
AMT 102 Encoder not working properly with VESC by DerpRush » Thu, 2019-07-25 11:32 |
5 |
by ripperpc Wed, 2022-04-06 21:36 |
|
|
Using UART from LabVIEW by hannnes » Tue, 2022-04-05 15:19 |
0 |
by hannnes Tue, 2022-04-05 15:19 |
|
|
Adjusting Acceleration Ramp with NRF & Current control by Mido » Tue, 2022-04-05 14:36 |
0 |
by Mido Tue, 2022-04-05 14:36 |
|
|
VESC Battery Packs by frank » Tue, 2020-10-13 15:21 |
7 |
by dethei Mon, 2022-04-04 15:31 |
|
|
Corrupted firmware by Phill Dixon » Mon, 2022-04-04 08:27 |
2 |
by Phill Dixon Mon, 2022-04-04 10:50 |
|
|
VESC usefull for high speed regeneration? by Riccio » Fri, 2022-03-11 10:45 |
5 |
by Riccio Sat, 2022-04-02 11:21 |
|
|
Set RPM - reverse direction over CAN-Bus by 65273 » Tue, 2022-03-29 14:49 |
4 |
by 65273 Fri, 2022-04-01 15:53 |
|
|
Vesc 100/250 (Trampa board) wiring for ebike by Oded Mazor » Fri, 2022-03-18 23:34 |
8 |
by Markula Fri, 2022-04-01 09:21 |
|
|
PWM on output by ml2311 » Tue, 2021-08-24 14:46 |
5 |
by Flyingtux Wed, 2022-03-30 19:31 |
|
|
mcpwm_foc_adc_int_handler call frequency by Flyingtux » Tue, 2022-03-29 12:35 |
1 |
by Flyingtux Wed, 2022-03-30 19:21 |
|
|
VESC 100/250 IO Ports Protection by luke.flecknell » Wed, 2022-03-30 06:49 |
2 |
by luke.flecknell Wed, 2022-03-30 12:41 |
|
|
FOC and RC Helicopter (25KG) by Flyingtux » Tue, 2022-03-15 23:30 |
2 |
by Flyingtux Tue, 2022-03-29 17:12 |
|
|
[OT] Increase torque on DC brush motor by Riccio » Mon, 2022-03-28 19:32 |
2 |
by Riccio Tue, 2022-03-29 09:18 |
|
|
External Bluetooth and IMU on CAN-connected VESCs by frankus » Sat, 2022-03-26 19:58 |
0 |
by frankus Sat, 2022-03-26 19:58 |
|
|
2nd Maytech 75_300 burned by Flyingtux » Wed, 2022-03-16 22:15 |
1 |
by skyline1970 Fri, 2022-03-25 19:00 |
|
|
Heavy applications ? by nojjan » Mon, 2022-03-21 20:46 |
1 |
by skyline1970 Thu, 2022-03-24 21:26 |
|
|
IMU 9250 and 6050 not working on new vesc 4.12 and 4.20 by trung_qly » Sun, 2021-09-05 16:11 |
2 |
by skyline1970 Thu, 2022-03-24 20:57 |
|
|
ESP32 VESC controller by Ortsac » Fri, 2022-01-21 18:50 |
2 |
by Gatze Wed, 2022-03-23 10:50 |
|
|
ADC INPUT with 4.10 HW running with 5.02 FW by mouadh » Tue, 2022-03-22 15:32 |
0 |
by mouadh Tue, 2022-03-22 17:38 |
|
|
Cant connect to Flipsky 75100 by Ed222 » Sun, 2022-03-20 00:31 |
3 |
by Ed222 Sun, 2022-03-20 19:01 |
|
|
RC Car BLDC - Hall Effect Timing Angle Calculator by mendez » Mon, 2022-03-14 19:20 |
5 |
by sp3swj Sat, 2022-03-19 11:36 |
|
|
swap PWM H and PWM L Pins on STM32F4 by Urs_Harry » Tue, 2022-03-15 23:04 |
3 |
by skyline1970 Thu, 2022-03-17 09:58 |
|
|
VESC Blink codes by ligi » Wed, 2022-03-16 12:36 |
1 |
by frank Wed, 2022-03-16 14:57 |
|
|
FOC : Stop Motor without Active Brake by Flyingtux » Mon, 2022-03-14 12:35 |
4 |
by Flyingtux Tue, 2022-03-15 23:09 |
Log in to post new content in the forum.
