You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Shutdown mode by Akeela23 » Sat, 2023-05-06 01:50 |
1 |
by Akeela23 Sat, 2023-05-06 01:56 |
|
|
just receaved my awesome new vesc 6 plus however it wont configurate i get an errot message. :( by sabladask » Wed, 2023-05-03 16:15 |
2 |
by frank Fri, 2023-05-05 20:54 |
|
|
DUAL VESC FOR BIDIRECTIONAL ROTATION by Khaliduzzaman Mredul » Fri, 2023-05-05 06:46 |
0 |
by Khaliduzzaman Mredul Fri, 2023-05-05 11:00 |
|
|
[SOLVED] PWM speed control at low RPM by comes04 » Sun, 2023-04-16 13:30 |
1 |
by comes04 Wed, 2023-05-03 20:44 |
|
|
[SOLVED, was a mistake] Set ERPM command: issue with the speed controller with higher speed values that is possible with bat vol by yes_wecangogreen » Wed, 2023-04-12 00:51 |
1 |
by yes_wecangogreen Sat, 2023-04-29 09:24 |
|
|
Bench Testing by usaevo7 » Tue, 2023-04-25 16:50 |
0 |
by usaevo7 Tue, 2023-04-25 16:50 |
|
|
Vesc for 5000kW QS 205 Hub Motor ebike by Amiran » Fri, 2019-09-27 15:52 |
10 |
by vadicus Sun, 2023-04-23 01:23 |
|
|
VESC6 with DRV8320 by cromoly » Wed, 2023-04-19 02:40 |
0 |
by cromoly Wed, 2023-04-19 02:40 |
|
|
How does controlling two different motors over CAN bus really work? by oangelo » Sat, 2023-04-15 20:05 |
0 |
by oangelo Sat, 2023-04-15 20:05 |
|
|
HFI Mode Hoverboard Hub Motor by JulianT » Wed, 2023-04-12 19:16 |
0 |
by JulianT Sat, 2023-04-15 11:09 |
|
|
Position control of brushed dc motor with Vesc and REV through bore encoder by Greasy_D » Wed, 2023-03-29 20:17 |
14 |
by EnDeR_WiGiN Fri, 2023-04-14 17:48 |
|
|
GO-FOC G300 - shorted the USB connector shield to 72v by hedbrant » Tue, 2023-04-11 13:22 |
1 |
by hedbrant Thu, 2023-04-13 20:44 |
|
|
vesc canbus control PPM by JiaheXu » Thu, 2023-04-13 20:17 |
0 |
by JiaheXu Thu, 2023-04-13 20:17 |
|
|
Position Limits w/ BDC and ABI Encoder by gokulswami » Thu, 2023-04-13 10:43 |
0 |
by gokulswami Thu, 2023-04-13 10:43 |
|
|
VESC as Generator - Low Output at High Brake Current? by hoeken » Sat, 2021-08-28 17:42 |
8 |
by flydr2 Wed, 2023-04-12 20:38 |
|
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 » Wed, 2023-04-12 16:28 |
0 |
by Tom65 Wed, 2023-04-12 16:28 |
|
|
Able to read CAN messages from VESC but cannot write messages to CAN Bus. by willd3543 » Wed, 2023-04-05 23:49 |
3 |
by benjamin Wed, 2023-04-12 07:32 |
|
|
NEW and my motors sound like they work but hardly spin the wheels! by madurai85 » Sun, 2023-04-09 15:23 |
0 |
by madurai85 Sun, 2023-04-09 15:23 |
|
|
How to control PPM output with CANBUS command by JiaheXu » Thu, 2023-03-30 20:21 |
2 |
by JiaheXu Wed, 2023-04-05 16:52 |
|
|
FSESC 6.6 not Connecting to VESC Tool by billyredwood01 » Sat, 2020-11-28 12:34 |
12 |
by JP Mon, 2023-04-03 13:02 |
|
|
VESC - custom board by st0r » Wed, 2023-03-08 12:21 |
5 |
by st0r Sat, 2023-04-01 01:51 |
|
|
Dual VESC with UART communication (Arduino) - how to communicate with slave over can ? by GargiMan » Thu, 2019-01-03 01:56 |
21 |
by Shubham07 Fri, 2023-03-31 10:49 |
|
|
Can't get motor to run using COMM port on vesc 6 MKVI and arduino mega with a potentiometer and SolidGeeks UART library by Kokonenen » Thu, 2023-03-30 11:41 |
1 |
by Kokonenen Thu, 2023-03-30 16:19 |
|
|
please delete！ by return97 » Sat, 2022-07-23 17:31 |
4 |
by return97 Wed, 2023-03-29 17:28 |
|
|
Reverse polarity with 12V battery on Vesc 6, now giving fault codes by Kokonenen » Tue, 2023-03-28 13:45 |
2 |
by frank Wed, 2023-03-29 09:56 |
Log in to post new content in the forum.
