You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Wand (and app) not pairing by Jonny254 on Mon, 2019-10-07 15:17 |
3 |
by Daada Wed, 2022-04-27 10:58 |
General discussion | |
|
Control singular VESC using CAN-BUS and Arduino by Cam on Wed, 2021-01-06 10:29 |
4 |
by craiggault Wed, 2022-04-27 23:07 |
General discussion | |
|
Use sensors on the output shaft of a motor attached to a large gear ratio gearbox by davidq1688 on Wed, 2022-04-27 05:23 |
1 |
by tobiokanobi Thu, 2022-04-28 14:48 |
VESC Tool | |
|
Firmware by Phill Dixon on Mon, 2022-04-25 15:29 |
7 |
by frank Sat, 2022-04-30 14:21 |
General discussion | |
|
VESC Encoder connected to 12v by yanting Liu on Fri, 2022-04-29 07:53 |
1 |
by frank Sat, 2022-04-30 14:24 |
VESC Original Hardware | |
|
VESC 100/250: analog regen brake AND e-brake cut switch? by fatty on Thu, 2021-05-13 01:16 |
2 |
by frank Mon, 2022-05-02 09:11 |
General discussion | |
|
Previous tool+5.2 by Phill Dixon on Sun, 2022-05-01 07:50 |
1 |
by frank Mon, 2022-05-02 09:12 |
General discussion | |
|
VESC output current decreasing in time by isso777 on Sat, 2022-04-30 14:59 |
5 |
by isso777 Mon, 2022-05-02 17:30 |
General discussion | |
|
VESC 100V 250A - don't reach 50000ERPM by tobiokanobi on Tue, 2022-04-12 19:29 |
6 |
by tobiokanobi Mon, 2022-05-02 19:22 |
VESC Original Hardware | |
|
Insufficient torque at low RPM by isso777 on Sat, 2022-04-23 21:13 |
10 |
by frank Tue, 2022-05-03 08:18 |
General discussion | |
|
CAN Analyzer by min on Tue, 2022-05-03 10:38 |
by min Tue, 2022-05-03 10:38 |
General discussion | ||
|
Dual Vesc reading second wheel RPM by rdavenport3 on Tue, 2022-05-03 15:32 |
by rdavenport3 Tue, 2022-05-03 15:32 |
VESC Firmware | ||
|
Vesc can't connect to vesc tool by Roansky1 on Sat, 2022-04-30 13:05 |
3 |
by frank Tue, 2022-05-03 20:52 |
VESC Tool | |
|
VESC100/250 - motor current setting ignored? by tobiokanobi on Mon, 2022-05-02 13:27 |
3 |
by frank Tue, 2022-05-03 20:54 |
VESC Tool | |
|
Help with metr bluetooth Vesc does Not react by Necromenz on Fri, 2017-06-16 15:32 |
47 |
by Gatze Wed, 2022-05-04 13:17 |
VESC6 Beta | |
|
Fsesc 75100 current heavily oscillating by xmp on Wed, 2022-05-04 17:55 |
by xmp Wed, 2022-05-04 17:55 |
Third Party Hardware | ||
|
Current filters on VESC MKIII? by Elwin on Sat, 2021-11-06 11:16 |
7 |
by vadicus Thu, 2022-05-05 01:26 |
General discussion | |
|
How is Motor Temperature measured? by shimdidly on Mon, 2017-10-02 07:52 |
4 |
by drummerboy5408 Thu, 2022-05-05 05:06 |
General discussion | |
|
Multiple "Custom User Apps" Selectable from VESC Tool by tpal on Thu, 2022-05-05 18:43 |
1 |
by Gatze Thu, 2022-05-05 22:11 |
General discussion | |
|
Absolute max current by Phill Dixon on Thu, 2022-05-05 18:10 |
1 |
by vadicus Fri, 2022-05-06 02:55 |
General discussion |
Pages
