You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Ayuda español by julitosanse on Wed, 2021-01-27 03:49 |
3 |
by skyline1970 Thu, 2021-01-28 21:01 |
The VESC-Project | |
|
uart position control by kragon on Sun, 2021-01-24 13:34 |
1 |
by kragon Thu, 2021-01-28 16:46 |
General discussion | |
|
Custom hardware flash problems by brightlightbeam on Mon, 2021-01-25 17:25 |
4 |
by brightlightbeam Thu, 2021-01-28 12:00 |
Third Party Hardware | |
|
DRV8301 Gate Drive value in Control Register by shaman on Thu, 2019-10-17 04:22 |
4 |
by Rovimo Thu, 2021-01-28 11:14 |
VESC Firmware | |
|
PWM outputs on Hall1 and Hall2 pins by brentfpage on Mon, 2020-08-31 01:32 |
2 |
by mechatronixNick Wed, 2021-01-27 08:53 |
VESC Original Hardware | |
|
firmware version by Brian123 on Sat, 2021-01-23 06:48 |
1 |
by Brian123 Sat, 2021-01-23 07:35 |
General discussion | |
|
FlipSky 75/300 + Alien 80 KV noise/vibration under load by brendangillatt on Thu, 2021-01-07 01:19 |
12 |
by vadicus Fri, 2021-01-22 18:14 |
General discussion | |
|
Install VESC on ubuntu 18.04 bionic not working by rest_vesc_001 on Fri, 2020-12-11 18:25 |
1 |
by RitaGilmore Fri, 2021-01-22 16:36 |
VESC Tool | |
|
Can't program bricked Vesc 6 over SWD by Rc 44 on Thu, 2019-06-20 02:16 |
6 |
by amit_bhar Thu, 2021-01-21 19:09 |
VESC Original Hardware | |
|
Deceleration Curve by slick on Sun, 2019-07-21 21:10 |
2 |
by kylerlaird Thu, 2021-01-21 17:31 |
Feature Requests | |
|
is VESC compatible with ROS by Knightfluffy on Fri, 2021-01-15 02:31 |
1 |
by TechAUmNu Sat, 2021-01-16 14:05 |
General discussion | |
|
Реверс вращения двигателя by Wolod5 on Sat, 2021-01-16 09:59 |
2 |
by Wolod5 Sat, 2021-01-16 12:21 |
VESC Tool | |
|
Custom Battery Settings? Inaccurate Wh readings? by dfelz on Wed, 2020-04-08 02:04 |
3 |
by starset Wed, 2021-01-13 22:54 |
VESC Tool | |
|
CAN not working on VESC MkV by chundri on Tue, 2021-01-12 15:06 |
1 |
by chundri Wed, 2021-01-13 15:48 |
VESC Original Hardware | |
|
FOC detection not working, "L=0" by chundri on Tue, 2021-01-12 15:02 |
2 |
by chundri Wed, 2021-01-13 15:40 |
VESC Tool | |
|
Reusing pin in custom application by Pechvogel on Wed, 2021-01-13 07:12 |
by Pechvogel Wed, 2021-01-13 07:12 |
VESC Firmware | ||
|
motor to slow and no power by Thiery Vardon on Sat, 2021-01-09 10:45 |
2 |
by Thiery Vardon Tue, 2021-01-12 13:27 |
VESC Tool | |
|
Robotics focussed mini VESC 6 derivative by StefanH on Tue, 2021-01-12 12:52 |
by StefanH Tue, 2021-01-12 12:52 |
Third Party Hardware | ||
|
VESC 75/300 Configuration problems with Hacker Q80 Motors by electricfox on Thu, 2019-02-28 18:23 |
13 |
by Cherry Tue, 2021-01-12 11:56 |
VESC Tool | |
|
HALL-FOC---don't understand the mcpwm_foc_hall_detect() function by ConnerL on Wed, 2021-01-06 12:33 |
2 |
by ConnerL Tue, 2021-01-12 02:55 |
General discussion |
Pages
