You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
terminal command via UART for a gimbal by fredfred on Sat, 2021-12-18 20:49 |
by fredfred Sat, 2021-12-18 20:49 |
VESC Tool | ||
|
Help i can not setup my motors by jakson01 on Fri, 2022-09-09 18:37 |
by jakson01 Fri, 2022-09-09 18:37 |
VESC Tool | ||
|
VESC ADC1 throttle configuration like an EV-Rekuperation by sega on Wed, 2024-06-12 17:48 |
by sega Wed, 2024-06-12 17:48 |
General discussion | ||
|
Can I re-use an old Galaxy S3 to run the VESC tool? by Munkyheed on Fri, 2019-08-02 20:00 |
by Munkyheed Fri, 2019-08-02 20:00 |
VESC Tool | ||
|
FSESC 4.12 mini help fixing 3.3v rail by stefann on Sun, 2022-08-28 10:15 |
by stefann Wed, 2022-08-31 10:31 |
Third Party Hardware | ||
|
Reversed polarity on one of my controllers when setting up by jsherbz92 on Sun, 2025-05-25 15:16 |
by jsherbz92 Sun, 2025-05-25 15:16 |
General discussion | ||
|
Connecting handlebar controlls by mannberg on Thu, 2022-03-10 14:57 |
by mannberg Thu, 2022-03-10 14:57 |
General discussion | ||
|
Controller 75100 by nilo on Sun, 2024-05-26 21:27 |
by nilo Sun, 2024-05-26 21:27 |
General discussion | ||
|
problem with encoder readings for proper feedback using arduino by ruthvikchanda on Thu, 2018-12-06 07:05 |
by ruthvikchanda Thu, 2018-12-06 07:05 |
General discussion | ||
|
The engine stopped spinning after updating firmware by brian adilman on Wed, 2022-01-26 17:40 |
by brian adilman Wed, 2022-01-26 19:15 |
VESC Firmware | ||
|
Bluemind 80V/450A and 100V/550A by qdxiatao on Tue, 2023-05-09 05:47 |
by qdxiatao Tue, 2023-05-09 05:47 |
Third Party Hardware | ||
|
VESC Tool TCP server, how to start connection to VESC ? by pf26 on Wed, 2025-11-12 16:13 |
by pf26 Wed, 2025-11-12 16:14 |
VESC Tool | ||
|
vesc tool v1.05 fw 3.51 by at_dts on Wed, 2020-09-23 20:12 |
by at_dts Wed, 2020-09-23 20:12 |
VESC Firmware | ||
|
Controlling (HB) Braking from Arduino by Bruce on Sat, 2021-02-27 00:23 |
by Bruce Sat, 2021-02-27 00:23 |
General discussion | ||
|
Yet another failed connection.... by MiguelXJ on Mon, 2024-01-01 19:28 |
by MiguelXJ Mon, 2024-01-01 19:28 |
VESC Tool | ||
|
Sensored mode studering by dtmpro621 on Thu, 2023-03-02 04:40 |
by dtmpro621 Thu, 2023-03-02 05:25 |
General discussion | ||
|
Prevent Wheel-slip by low-pass filtering duty cycle output by AlexBenn on Thu, 2018-09-13 07:50 |
by AlexBenn Thu, 2018-09-13 07:50 |
VESC Firmware | ||
|
Communication over UART or CAN by JCLNEIL on Wed, 2023-12-13 14:36 |
by JCLNEIL Wed, 2023-12-13 14:36 |
VESC Tool | ||
|
75/300 R2 FW higher than 3.62 ? it is possible? by Lasse on Sat, 2020-12-26 20:34 |
by Lasse Sat, 2020-12-26 20:34 |
VESC Firmware | ||
|
Install VESC on ubuntu 18.04 bionic by rest_vesc_001 on Tue, 2020-12-08 15:34 |
by rest_vesc_001 Tue, 2020-12-08 15:34 |
General discussion |
Pages
