You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Regenerative braking in scooter Zero x11 72V dual motor 2 x 1600 w peak power 6000W by Makroman on Wed, 2020-07-08 20:00 |
by Makroman Wed, 2020-07-08 20:00 |
General discussion | ||
|
Protect psu from regenerative braking by KarlGreger on Tue, 2020-01-28 03:45 |
4 |
by marc.s.cohn@gma... Tue, 2020-07-07 21:11 |
General discussion | |
|
ADC input protection proposal by arestechfinland on Mon, 2020-07-06 19:41 |
by arestechfinland Mon, 2020-07-06 19:41 |
General discussion | ||
|
Regen Braking / Braking Current under Different Voltages by kimjungyeop on Tue, 2020-02-25 23:47 |
2 |
by Makroman Mon, 2020-07-06 11:58 |
General discussion | |
|
Using VESC to drive sensorless linear motor to simulate on/off solenoid by cmcraeslo on Wed, 2020-07-01 09:15 |
1 |
by pf26 Mon, 2020-07-06 11:10 |
General discussion | |
|
FOC Motor Detection Values Incorrect, PID Tuning Advice? by bmwman91 on Mon, 2020-07-06 03:09 |
by bmwman91 Mon, 2020-07-06 03:21 |
VESC Tool | ||
|
Regen braking not working? by forcefed on Thu, 2018-04-05 01:57 |
3 |
by Makroman Sun, 2020-07-05 16:12 |
General discussion | |
|
Bug Report - Motor/App Data not saved to VESC by bb67 on Sun, 2020-06-21 10:26 |
1 |
by bb67 Sat, 2020-07-04 12:21 |
VESC Tool | |
|
VESC 6 Mark III and Traxxas Summit Radio Receiver PWM / PPM Signals by j98221@gmail.com on Fri, 2020-07-03 07:27 |
by j98221@gmail.com Fri, 2020-07-03 07:27 |
General discussion | ||
|
simulate turboprop engine ... using VESC, how to.... by Eckehard on Wed, 2020-06-10 22:32 |
17 |
by Eckehard Thu, 2020-07-02 22:34 |
General discussion | |
|
Runaway Motor with No BLE by Marctwo on Thu, 2020-07-02 20:47 |
by Marctwo Thu, 2020-07-02 20:47 |
General discussion | ||
|
connecting vesc tool with Prototipo by Govert on Thu, 2020-07-02 19:43 |
by Govert Thu, 2020-07-02 19:43 |
General discussion | ||
|
Vesc firmware update by ron18923 on Sun, 2019-06-16 18:29 |
4 |
by MollyEskam Thu, 2020-07-02 16:49 |
VESC Firmware | |
|
Requesting fault codes over UART by spork on Wed, 2020-06-24 09:02 |
1 |
by Pimousse Wed, 2020-07-01 12:50 |
General discussion | |
|
Max RPM by donrecardo on Thu, 2020-06-25 12:00 |
1 |
by Tibor Kalman Za... Mon, 2020-06-29 21:03 |
VESC Tool | |
|
Optimizing VESC6 setup for my Giant Lego Go-Kart project by mantisrobot on Thu, 2020-06-18 13:29 |
3 |
by TechAUmNu Mon, 2020-06-29 10:19 |
General discussion | |
|
App Config disabled one side problem by timfame11 on Sat, 2020-06-27 00:26 |
by timfame11 Sun, 2020-06-28 05:21 |
VESC Tool | ||
|
Firmware Updating to run X2 Pro remote for VESC6.6 by Caddy on Sat, 2020-06-27 19:30 |
by Caddy Sat, 2020-06-27 19:30 |
VESC Firmware | ||
|
Please remove bootloader update section from FW Tab by sunbeam on Sun, 2019-09-15 01:12 |
1 |
by TechAUmNu Sat, 2020-06-27 09:33 |
VESC Tool | |
|
150V 300A - Am I missing something? by eptv on Fri, 2020-06-26 09:04 |
1 |
by vadicus Fri, 2020-06-26 20:55 |
Third Party Hardware |
Pages
