You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
VESC hw4.7 firmware update in vesc tool (2.06) fails with "Erase timed out" by snowcrazed on Thu, 2020-07-23 05:47 |
2 |
by Maxid Mon, 2025-05-12 10:27 |
VESC Original Hardware | |
|
config wanted, for 75100 with ebike geared hub motor by tom355 on Mon, 2023-02-20 09:51 |
3 |
by JanneHooo Sun, 2025-05-11 19:17 |
Third Party Hardware | |
|
Vesc 4.12 USB Issues by puravida13 on Tue, 2025-05-06 18:45 |
1 |
by puravida13 Sat, 2025-05-10 01:53 |
General discussion | |
|
Sensorless Homing: Move motor between two endstops by LISMS on Fri, 2025-05-09 00:50 |
by LISMS Fri, 2025-05-09 00:50 |
Projects incorporating VESC technology | ||
|
PID Speed Mode not limiting max ERPM by jordan73s on Sat, 2025-05-03 10:57 |
1 |
by colmor Thu, 2025-05-08 22:44 |
General discussion | |
|
Vesc PAS (Pedal Assist) by Evwan on Sat, 2022-07-02 04:37 |
6 |
by wraven Wed, 2025-05-07 14:40 |
VESC Tool | |
|
VESC 6 plus working but no servo response by saspragkathos on Mon, 2020-06-29 17:28 |
1 |
by Shreeram2311 Tue, 2025-05-06 02:44 |
VESC Firmware | |
|
UART Servo Output Works in VESC‑Tool UI but Not via ROS Publish by Shreeram2311 on Tue, 2025-05-06 02:40 |
by Shreeram2311 Tue, 2025-05-06 02:40 |
VESC Tool | ||
|
FlipSky 75/300 + Alien 80 KV noise/vibration under load by brendangillatt on Thu, 2021-01-07 01:19 |
13 |
by Thejesh Bollineni Wed, 2025-04-30 22:49 |
General discussion | |
|
Connect VESC4.7 over USB by Lars_Dierickx on Thu, 2023-03-09 16:13 |
4 |
by Lawrence Sun, 2025-04-27 16:23 |
VESC Tool | |
|
Flipsky 75200 Motor ruckelt und wird sehr schnell heiß by Oriessin on Sat, 2025-04-26 07:38 |
by Oriessin Sat, 2025-04-26 07:38 |
General discussion | ||
|
VESC in-air startup failure by jschall on Sat, 2025-04-26 00:56 |
2 |
by jschall Sat, 2025-04-26 01:32 |
General discussion | |
|
What is the current state of mcus support? by il_piccione on Fri, 2025-04-25 09:47 |
by il_piccione Fri, 2025-04-25 09:47 |
General discussion | ||
|
VESC Flipsky 75100 used in Ryobi RM480e electric riding mower. by Ryobi master on Tue, 2024-02-27 00:20 |
2 |
by BuffaloBub Fri, 2025-04-25 01:10 |
Projects incorporating VESC technology | |
|
vesc disconnected during detection by TonyYuan on Mon, 2023-06-26 09:17 |
2 |
by powerpedalph Thu, 2025-04-24 07:51 |
VESC Firmware | |
|
Projet kukirin g2 master + Flipsky 75200pro v2(maître)+ Flipsky 75200(esclave)+ écran tft Flipsky by Cédric Lécuyer on Sun, 2025-04-20 13:10 |
1 |
by electricfox Sun, 2025-04-20 16:32 |
Projects incorporating VESC technology | |
|
Does Trampa BMS work with multiple VESCs? by kylerlaird on Sun, 2025-04-20 03:57 |
2 |
by kylerlaird Sun, 2025-04-20 15:38 |
VESC Original Hardware | |
|
No activity in CAN analyzer by PutridFox on Sat, 2025-04-19 08:52 |
1 |
by PutridFox Sat, 2025-04-19 21:06 |
General discussion | |
|
VESC crashes on Servo output by AutonomousDrifting on Fri, 2021-02-05 13:25 |
7 |
by dawgs Sat, 2025-04-19 12:40 |
General discussion | |
|
Is BMS Tool compatible with LTO batteries? by SteveBrantley on Fri, 2025-04-18 23:12 |
by SteveBrantley Fri, 2025-04-18 23:12 |
General discussion |
Pages
