You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Custom firmware workflow by BDJ on Fri, 2021-09-10 13:50 |
by BDJ Fri, 2021-09-10 13:50 |
VESC Firmware | ||
|
Vesc repair guidances by Booya on Tue, 2020-03-10 17:31 |
3 |
by oschlueter Fri, 2021-09-10 12:10 |
VESC Original Hardware | |
|
Sensored acceleration vs sensorless by Mastersam on Tue, 2021-06-01 11:48 |
1 |
by miskuhunor@gmail.com Thu, 2021-09-09 09:41 |
VESC Tool | |
|
Several questions and safe values by miskuhunor@gmail.com on Thu, 2021-09-09 08:33 |
by miskuhunor@gmail.com Thu, 2021-09-09 08:33 |
VESC Tool | ||
|
Limp mode via CAN by totalgeek9224 on Mon, 2020-02-10 14:37 |
3 |
by A2 Wed, 2021-09-08 21:20 |
Feature Requests | |
|
Power Switch by flyingbrike on Wed, 2021-09-08 13:47 |
by flyingbrike Wed, 2021-09-08 13:47 |
General discussion | ||
|
Stutter start by benha on Tue, 2021-08-17 14:30 |
3 |
by flyingbrike Wed, 2021-09-08 13:45 |
General discussion | |
|
VESC 75/300 vs VESC 100/250 by XBO on Tue, 2021-09-07 19:31 |
3 |
by flyingbrike Wed, 2021-09-08 13:42 |
General discussion | |
|
vesc tool 1.25 not opening. by osis on Tue, 2019-10-29 20:50 |
9 |
by flyingbrike Wed, 2021-09-08 09:06 |
VESC Tool | |
|
Dshot and uavcan protocol support by Roadead on Wed, 2021-09-08 06:09 |
by Roadead Wed, 2021-09-08 06:09 |
Feature Requests | ||
|
Regen question by proget.snc on Thu, 2021-09-02 14:36 |
2 |
by proget.snc Fri, 2021-09-03 11:50 |
General discussion | |
|
Question about FOC Wizard by proget.snc on Thu, 2021-08-26 16:31 |
2 |
by proget.snc Thu, 2021-09-02 14:23 |
VESC Tool | |
|
VESC Tool RPM not the actual in real life by Poh Boon pin on Sun, 2021-07-11 16:00 |
2 |
by hoeken Wed, 2021-09-01 15:56 |
VESC Tool | |
|
Interested in software, computer science student by coddy on Mon, 2020-04-27 22:52 |
1 |
by hoeken Wed, 2021-09-01 15:53 |
General discussion | |
|
Battery current limit problems by ziumus on Mon, 2021-08-30 21:37 |
by ziumus Mon, 2021-08-30 21:37 |
General discussion | ||
|
current control via CAN not working by STTS on Thu, 2021-08-12 11:51 |
2 |
by mm_iem Mon, 2021-08-30 18:00 |
VESC Tool | |
|
Downloading VESC tool on a mac? by Taliesin on Mon, 2018-04-30 01:28 |
3 |
by txdad Fri, 2021-08-27 17:41 |
General discussion | |
|
FSESC 4.2 Firmware Resetting by Pranay on Fri, 2021-08-27 12:18 |
1 |
by TechAUmNu Fri, 2021-08-27 17:20 |
General discussion | |
|
Built in BLE HD60 not Working by CS on Mon, 2021-08-23 13:21 |
3 |
by frank Thu, 2021-08-26 08:09 |
VESC Original Hardware | |
|
Loud Bang at Sensor-less Switchover with hub motor by hackeybabel on Sat, 2021-08-21 11:13 |
2 |
by hackeybabel Thu, 2021-08-26 07:19 |
General discussion |
Pages
