You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
FlipSky 75/300 + Alien 80 KV noise/vibration under load by brendangillatt on Thu, 2021-01-07 01:19 |
13 |
by Thejesh Bollineni Wed, 2025-04-30 22:49 |
General discussion | |
|
VESC 75/300 Configuration problems with Hacker Q80 Motors by electricfox on Thu, 2019-02-28 18:23 |
13 |
by Cherry Tue, 2021-01-12 11:56 |
VESC Tool | |
|
F50-300 (Design Not Tested yet) by mrendu43 on Tue, 2021-03-09 11:49 |
13 |
by mrendu43 Sat, 2021-05-01 17:15 |
Third Party Hardware | |
|
VESC-Tool Bugs by Danny Bokma on Sun, 2017-06-04 01:44 |
13 |
by sevenfloorsdown Wed, 2022-03-23 22:45 |
VESC6 Beta | |
|
Driving 2 BLDC motors with one MCU by Pimousse on Tue, 2018-06-26 15:42 |
13 |
by wkt Wed, 2018-10-17 14:02 |
Third Party Hardware | |
|
Can't connect to slave vesc via master usb in vesc-tool -SOLVED- by rich on Mon, 2017-07-24 13:31 |
13 |
by fadez Tue, 2019-09-17 14:11 |
VESC6 Beta | |
|
swagatron hoverboard motors with VESC by popeye243 on Tue, 2020-07-21 02:49 |
13 |
by popeye243 Mon, 2020-09-07 03:42 |
General discussion | |
|
2 vs 3 phase shunts by antonchromjak on Sun, 2018-04-15 13:25 |
13 |
by TechAUmNu Fri, 2019-02-15 18:57 |
General discussion | |
|
PYVESC UART Issues by goethe on Fri, 2017-12-29 21:36 |
13 |
by petertaylor Tue, 2018-09-25 10:06 |
VESC Firmware | |
|
Flipsky FSESC75100 & FSESC75200 Phase Filtering by j.konrad on Sat, 2022-04-02 00:17 |
13 |
by Fr33man Mon, 2025-06-02 17:33 |
Third Party Hardware | |
|
Two VESCs, two three-phase windings, one motor stator by kubark42 on Fri, 2021-11-12 21:29 |
13 |
by skyline1970 Fri, 2021-11-19 20:05 |
General discussion | |
|
The selected file is too large to be a firmware. by vinci on Wed, 2022-04-20 18:50 |
13 |
by makentor Thu, 2022-12-08 18:19 |
VESC Firmware | |
|
ADC pin voltage not zero by zoppp on Fri, 2019-02-08 23:44 |
12 |
by zoppp Tue, 2019-03-12 01:17 |
General discussion | |
|
FSESC 6.6 not Connecting to VESC Tool by billyredwood01 on Sat, 2020-11-28 12:34 |
12 |
by JP Mon, 2023-04-03 13:02 |
General discussion | |
|
Adjusting Beta Value for Motor Thermistor. by Ecyclist on Thu, 2018-12-06 23:22 |
12 |
by Ecyclist Tue, 2019-01-29 04:29 |
VESC Tool | |
|
Trying to connect over USB, but new 6.4 connects and disconnects a few seconds later. by MaxMaker1 on Thu, 2018-05-24 16:15 |
12 |
by frank Thu, 2019-02-21 20:34 |
VESC Tool | |
|
Motors spin up during detection but then won't move by jordan314 on Thu, 2019-02-21 09:18 |
12 |
by KDoc Tue, 2023-01-17 00:13 |
VESC Tool | |
|
CANBUS communication documentation by Dillon on Sun, 2017-08-27 17:50 |
12 |
by simonpamies Thu, 2025-07-10 14:21 |
VESC6 Beta | |
|
Hoverboard Motor with VESC by mados73 on Wed, 2018-03-21 22:14 |
12 |
by Kirkness Mon, 2020-07-13 01:00 |
General discussion | |
|
temp motor by emmaanuel on Wed, 2017-09-13 01:27 |
12 |
by Roger Wolff Wed, 2017-11-08 16:23 |
VESC Firmware |
Pages
