You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Setting an ERPM limit for one motor based off another motors ERPM by NijiflianBustock on Fri, 2023-07-07 18:37 |
by NijiflianBustock Fri, 2023-07-07 18:37 |
Feature Requests | ||
|
Power Monitor and Logging by IntDesign on Thu, 2023-07-06 18:08 |
by IntDesign Thu, 2023-07-06 18:08 |
VESC Tool | ||
|
DBC development by flatspot on Mon, 2020-11-09 08:56 |
1 |
by Erosand Thu, 2023-07-06 15:37 |
VESC Firmware | |
|
Sensored BLDC mode confusion by srinath on Wed, 2023-07-05 15:45 |
by srinath Wed, 2023-07-05 15:49 |
VESC Tool | ||
|
Error message by DAVCRO on Thu, 2023-03-09 17:15 |
1 |
by Gos1 Wed, 2023-07-05 13:17 |
Projects incorporating VESC technology | |
|
Settings by aquamarin on Sat, 2023-07-01 16:11 |
by aquamarin Sat, 2023-07-01 16:11 |
General discussion | ||
|
Cut off after reaching Max. Duty Cycle by toboli on Thu, 2023-06-01 22:54 |
2 |
by toboli Sat, 2023-07-01 13:32 |
General discussion | |
|
xESC2 mini - a small, low power VESC derivative for robotics use by clemens.elflein on Fri, 2022-03-04 14:44 |
2 |
by Mowman Fri, 2023-06-30 22:51 |
Third Party Hardware | |
|
E-bike set up by Iangamblin on Fri, 2023-03-24 14:02 |
5 |
by Iangamblin Thu, 2023-06-29 17:35 |
General discussion | |
|
Limit battery voltage during regen by f.damien12 on Mon, 2022-03-28 12:40 |
14 |
by drummerboy5408 Wed, 2023-06-28 05:33 |
General discussion | |
|
Latched power switch on Trampa VESC 6 75A by dversity on Wed, 2023-06-28 00:36 |
by dversity Wed, 2023-06-28 00:36 |
VESC Tool | ||
|
Motors spin during detection but then won't spin by jsbenson on Tue, 2023-06-27 23:54 |
by jsbenson Tue, 2023-06-27 23:54 |
General discussion | ||
|
Version 2.03 won't open by marialoise on Fri, 2020-03-13 20:24 |
5 |
by pwilkinson91 Tue, 2023-06-27 22:07 |
VESC Tool | |
|
Can someone verify this by jsbenson on Mon, 2023-06-26 09:22 |
by jsbenson Tue, 2023-06-27 07:50 |
General discussion | ||
|
What is ADC3 used for in VESC6 by Tilman Baumann on Tue, 2018-04-10 11:12 |
3 |
by Gos1 Mon, 2023-06-26 13:56 |
VESC Original Hardware | |
|
(Watchdog) - Resets with multipole engine. by edilger on Mon, 2023-06-26 12:33 |
by edilger Mon, 2023-06-26 12:33 |
VESC Firmware | ||
|
Switching control scheme during opertion by Ben Murton on Tue, 2023-01-31 02:57 |
1 |
by Gos1 Mon, 2023-06-26 12:07 |
General discussion | |
|
New at VESC Tool by TheButaner on Sun, 2023-06-04 21:38 |
1 |
by Gos1 Mon, 2023-06-26 11:37 |
General discussion | |
|
Dual throttle inputs by olletj on Wed, 2022-08-10 23:56 |
2 |
by Gos1 Mon, 2023-06-26 11:34 |
General discussion | |
|
How to set up 60 degree hall sensors? by ryde6 on Sat, 2021-06-05 12:45 |
1 |
by Jan Jaroš Sat, 2023-06-24 13:47 |
VESC Tool |
Pages
