You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
BATTERY_VOLTAGE_HIGH_CUTOFF_START // CUTOFF_END ? by Andy G on Mon, 2023-10-16 18:41 |
by Andy G Mon, 2023-10-16 18:43 |
General discussion | ||
|
Setting up flipsky by JanneHooo on Sat, 2023-10-14 13:07 |
2 |
by JanneHooo Sun, 2023-10-15 13:18 |
General discussion | |
|
Usb not working. by hummina on Tue, 2023-10-10 22:48 |
2 |
by hummina Fri, 2023-10-13 20:48 |
General discussion | |
|
FOC for BDC? by SlimSh8y on Thu, 2018-07-12 23:05 |
11 |
by JanneHooo Fri, 2023-10-13 18:20 |
VESC Tool | |
|
Regen on fully charged battery: soft high voltage limit by e404 on Wed, 2019-02-20 16:15 |
6 |
by Andy G Fri, 2023-10-13 14:26 |
General discussion | |
|
Need Your Help with PPM Mapping Remote during Setup by silverglate on Sun, 2019-02-03 05:04 |
32 |
by RCHAL158 Fri, 2023-10-13 10:30 |
Third Party Hardware | |
|
Motors in PID control stops responding for a few seconds by rcmower on Tue, 2023-10-10 20:49 |
2 |
by rcmower Thu, 2023-10-12 14:19 |
General discussion | |
|
Programmable freewheel function by baumeister on Wed, 2023-10-11 09:16 |
by baumeister Thu, 2023-10-12 11:08 |
VESC Tool | ||
|
Configuration Issue with Dual FlipSky 75100 Controllers by daktylus on Thu, 2023-10-12 03:17 |
by daktylus Thu, 2023-10-12 03:17 |
VESC Tool | ||
|
Most reliable control of VESC? by ProgramThyself on Wed, 2023-10-11 06:29 |
1 |
by vadicus Thu, 2023-10-12 03:13 |
VESC Firmware | |
|
i try, i try but... by rastafouille on Tue, 2023-10-10 16:19 |
by rastafouille Tue, 2023-10-10 16:21 |
VESC Tool | ||
|
VESC FOC in Encoder Mode Unstable at High eRPM by bayetan on Sun, 2023-10-08 22:40 |
2 |
by bayetan Mon, 2023-10-09 16:20 |
VESC Firmware | |
|
RPM not Working? by ngilchr on Fri, 2023-10-06 16:39 |
1 |
by bayetan Sun, 2023-10-08 23:03 |
VESC Tool | |
|
Connect multiple VESCs together and communicate over CAN by mustard666 on Fri, 2023-10-06 23:32 |
by mustard666 Fri, 2023-10-06 23:32 |
General discussion | ||
|
Juddering on startup by ecliptalyst on Fri, 2023-10-06 00:47 |
by ecliptalyst Fri, 2023-10-06 00:47 |
General discussion | ||
|
How to get vesc tool for linux on ubuntu? by vitormhenrique on Tue, 2019-10-22 16:00 |
7 |
by JackGunnarsson Mon, 2023-10-02 13:20 |
VESC Tool | |
|
Motor Controller Recommendations - 84V max - 50A Continuous by dylanu on Thu, 2021-11-11 22:54 |
5 |
by mikael Sat, 2023-09-30 01:46 |
General discussion | |
|
Help needed compiling vesc express for esp32 mini D1 by mrendu43 on Sun, 2023-02-05 18:00 |
2 |
by meashman Fri, 2023-09-29 23:34 |
VESC Firmware | |
|
MINI4 (Page: 1, 2)
by antonchromjak on Sun, 2017-11-26 16:08 |
61 |
by roque.canales Fri, 2023-09-29 13:54 |
Third Party Hardware | |
|
Hub motor e-bike not recognized by olivierskypullc... on Tue, 2019-04-16 11:06 |
3 |
by Ampit Fri, 2023-09-29 12:38 |
VESC Original Hardware |
Pages
