You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Show actual encoder RPM by Enak on Fri, 2017-09-08 01:05 |
2 |
by Roger Wolff Sun, 2018-09-16 09:47 |
Feature Requests | |
|
Speed control tuning for 500-1000 RPM by vadimz on Sun, 2018-09-02 18:09 |
2 |
by vadimz Sat, 2018-09-15 14:08 |
General discussion | |
|
FAULT_CODE_DRV Motor not spinning by Mightyorc on Sat, 2018-09-15 03:36 |
by Mightyorc Sat, 2018-09-15 03:36 |
General discussion | ||
|
Maytech esc 5V rail reads 0.5v by hhhhghg on Fri, 2018-09-14 13:23 |
by hhhhghg Fri, 2018-09-14 13:23 |
Third Party Hardware | ||
|
Cut-out at >40A by thewho on Thu, 2018-09-13 20:24 |
by thewho Thu, 2018-09-13 20:24 |
General discussion | ||
|
FOC detection needs load? by tuloski on Thu, 2018-09-13 10:19 |
1 |
by TechAUmNu Thu, 2018-09-13 12:26 |
VESC Tool | |
|
AS5048A and the AS5047D Problems. by raess on Wed, 2018-04-04 14:05 |
2 |
by liqikai Thu, 2018-09-13 10:47 |
General discussion | |
|
Cannot get any PPM signals from Arduino. Or is it just the VESC tool? by MaxMaker1 on Thu, 2018-06-21 23:06 |
4 |
by tuloski Thu, 2018-09-13 09:36 |
VESC Tool | |
|
Prevent Wheel-slip by low-pass filtering duty cycle output by AlexBenn on Thu, 2018-09-13 07:50 |
by AlexBenn Thu, 2018-09-13 07:50 |
VESC Firmware | ||
|
Flipsky 4.12 Vesc in FOC mode? by Jonny254 on Sat, 2018-09-08 11:25 |
3 |
by Jonny254 Thu, 2018-09-13 05:48 |
Third Party Hardware | |
|
Single shunt by andreas on Wed, 2018-09-12 22:17 |
by andreas Wed, 2018-09-12 22:17 |
Feature Requests | ||
|
Vesc and Arduino Interface with ppm control???? by ruthvikchanda on Mon, 2018-09-10 12:01 |
by ruthvikchanda Mon, 2018-09-10 12:01 |
General discussion | ||
|
VESC without Shunt Resistors/FOC by tul00985 on Mon, 2018-06-11 13:27 |
14 |
by tul00985 Mon, 2018-09-10 08:36 |
Third Party Hardware | |
|
Foc openloop soft start by Alan oldguy on Fri, 2018-09-07 03:05 |
by Alan oldguy Fri, 2018-09-07 03:05 |
Feature Requests | ||
|
Sudden motor stop by dmcke5 on Wed, 2018-08-15 13:50 |
2 |
by andreas Thu, 2018-09-06 20:48 |
General discussion | |
|
This and vedder.se forum? by hackish on Tue, 2017-11-07 19:29 |
2 |
by eRCaGuy Wed, 2018-09-05 02:37 |
The VESC-Project | |
|
Uploaded the wrong firmware, now I need help to debug :P by Frazatto on Tue, 2018-08-21 15:46 |
12 |
by Frazatto Tue, 2018-09-04 19:33 |
Third Party Hardware | |
|
How to erase whole flash with OpenOCD? by Frazatto on Mon, 2018-09-03 14:56 |
1 |
by Frazatto Tue, 2018-09-04 19:33 |
General discussion | |
|
Move FAULT pin to GPIOD_PIN2 by CTSchorsch on Tue, 2018-09-04 10:13 |
by CTSchorsch Tue, 2018-09-04 10:13 |
VESC Firmware | ||
|
How to read MotorRPM from UART to Arduino by azobe on Thu, 2018-03-08 14:42 |
3 |
by Pimousse Mon, 2018-09-03 14:31 |
General discussion |
Pages
