You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
two motors one ppm for throttle and one for the direction? by Robby Ertmann on Wed, 2021-04-21 13:48 |
by Robby Ertmann Wed, 2021-04-21 13:48 |
VESC Tool | ||
|
Two phase modulation by jguy on Sat, 2023-12-09 13:33 |
4 |
by jguy Fri, 2023-12-15 11:49 |
General discussion | |
|
Two Vesc6 MKV twin arrays ESC's - BMS CAN BUS connectivity by Spaceman on Fri, 2022-05-27 16:22 |
3 |
by Spaceman Fri, 2022-06-03 15:36 |
General discussion | |
|
Two VESCs with servo-out firmware by _saeed_arabi_ on Fri, 2019-12-13 22:22 |
1 |
by frank Thu, 2019-12-19 21:34 |
General discussion | |
|
Two vescs, one motor? by RoopeKuisma on Sun, 2020-05-10 22:11 |
17 |
by Elwin Thu, 2021-10-28 09:48 |
General discussion | |
|
Two VESCs, two three-phase windings, one motor stator by kubark42 on Fri, 2021-11-12 21:29 |
13 |
by skyline1970 Fri, 2021-11-19 20:05 |
General discussion | |
|
Type of Hall sensor by Faheem on Thu, 2023-10-12 05:52 |
3 |
by Faheem Mon, 2023-10-23 10:02 |
General discussion | |
|
Type of motors supported by VESC 6 MKIV by Sami Sahli on Thu, 2020-06-25 11:57 |
2 |
by Samuelx Tue, 2021-08-17 20:24 |
General discussion | |
|
UART Accel/Gyro/Mag data by NATUITION on Sat, 2019-12-28 11:25 |
3 |
by NATUITION Tue, 2020-01-07 22:14 |
General discussion | |
|
Uart and Usb tx not working by Camolas on Wed, 2025-11-26 08:08 |
by Camolas Wed, 2025-11-26 08:08 |
Third Party Hardware | ||
|
UART Arduino Monitor by arranto12 on Thu, 2021-11-18 00:24 |
by arranto12 Thu, 2021-11-18 00:24 |
General discussion | ||
|
UART CAN forwarding by frankus on Tue, 2019-01-29 16:07 |
4 |
by frankus Tue, 2021-02-16 06:35 |
General discussion | |
|
UART communication by EthB on Wed, 2017-09-06 19:13 |
19 |
by stefcux Thu, 2019-08-08 03:16 |
General discussion | |
|
UART for NRF51822 on "old" nrf pins ? by CTSchorsch on Fri, 2019-11-29 16:41 |
6 |
by hl0dk0 Tue, 2022-08-16 12:46 |
Feature Requests | |
|
UART GND to Battery (-), good idea ? by Pimousse on Sat, 2017-09-23 00:47 |
1 |
by Dillon Sat, 2018-03-17 05:56 |
General discussion | |
|
uart not working on vesc 4.10 latest firmware / hm-10 by daniel84uk on Sat, 2018-09-29 14:55 |
7 |
by acklavidian Wed, 2018-10-24 13:57 |
VESC Firmware | |
|
uart position control by kragon on Sun, 2021-01-24 13:34 |
1 |
by kragon Thu, 2021-01-28 16:46 |
General discussion | |
|
UART Safety Feature by jaghori.sasan on Wed, 2019-09-04 18:45 |
by jaghori.sasan Wed, 2019-09-04 18:45 |
VESC Tool | ||
|
UART Servo Output Works in VESC‑Tool UI but Not via ROS Publish by Shreeram2311 on Tue, 2025-05-06 02:40 |
by Shreeram2311 Tue, 2025-05-06 02:40 |
VESC Tool | ||
|
UART working great at low current, terrible at high current by Dillon on Sat, 2018-03-17 04:17 |
23 |
by Dillon Sat, 2019-01-19 04:06 |
VESC6 Beta |
Pages
