You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Motor temperature increase by e-biker on Sun, 2018-04-08 20:17 |
4 |
by e-biker Mon, 2018-04-09 14:44 |
General discussion | |
|
Latest Version 0.89? by renebormann on Mon, 2018-04-09 18:04 |
1 |
by renebormann Mon, 2018-04-09 18:38 |
VESC Tool | |
|
How to wire Cruise Control with VESC6 ADC by Tilman Baumann on Tue, 2018-04-10 11:11 |
by Tilman Baumann Tue, 2018-04-10 11:11 |
VESC Original Hardware | ||
|
Hall sensor filter on VESC flier board by raess on Tue, 2018-03-27 21:00 |
17 |
by raess Wed, 2018-04-11 13:43 |
General discussion | |
|
build VESC Tool on Linux Mint by cb on Fri, 2018-04-13 16:19 |
1 |
by benjamin Mon, 2018-04-16 10:59 |
VESC Tool | |
|
What is ADC3 used for in VESC6 by Tilman Baumann on Tue, 2018-04-10 11:12 |
2 |
by Tilman Baumann Mon, 2018-04-16 12:41 |
VESC Original Hardware | |
|
Extending current shunt amplifier voltage by TechAUmNu on Wed, 2018-04-11 00:43 |
2 |
by Roger Wolff Tue, 2018-04-17 08:56 |
General discussion | |
|
Problems with writing Firmware to the processor by Goex on Wed, 2018-03-28 09:11 |
2 |
by Idoff Tue, 2018-04-17 11:04 |
VESC Firmware | |
|
can't reach the maximum speed by kingpon on Sat, 2017-10-28 04:55 |
3 |
by elektrinis Tue, 2018-04-17 21:50 |
General discussion | |
|
Firmware 3.37 too old, unable to Connect VESC_Tool by Nico Isn on Wed, 2018-04-18 11:17 |
2 |
by Nico Isn Fri, 2018-04-20 16:31 |
VESC Firmware | |
|
Firmware update thru UART? by cromoly on Tue, 2018-04-17 01:19 |
4 |
by cromoly Fri, 2018-04-20 19:22 |
General discussion | |
|
Brakes completely repeatedly failing at high temperature by Paul15578 on Mon, 2018-03-26 13:06 |
10 |
by Paul15578 Sun, 2018-04-22 14:16 |
General discussion | |
|
OVER CURRENT without over current? by Oyta on Thu, 2018-04-19 23:26 |
3 |
by TheFallen Sun, 2018-04-22 14:43 |
VESC6 Beta | |
|
Some ideas to improve VESC by e-biker on Sun, 2018-03-18 16:36 |
3 |
by Roger Wolff Mon, 2018-04-23 08:57 |
Feature Requests | |
|
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 on Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
General discussion | |
|
Duty vs RPM for smooth start and slow running by Davideo on Tue, 2018-04-24 14:42 |
by Davideo Tue, 2018-04-24 14:42 |
General discussion | ||
|
Dollar signs break private messages by TechAUmNu on Tue, 2018-04-24 18:09 |
by TechAUmNu Tue, 2018-04-24 18:09 |
General discussion | ||
|
Cannot upgrade firmware by greensightag.com on Fri, 2018-04-27 02:32 |
by greensightag.com Fri, 2018-04-27 02:34 |
VESC Firmware | ||
|
The motor with an enkoder of AS5048 rotates unevenly by densor on Thu, 2018-04-26 11:41 |
2 |
by densor Fri, 2018-04-27 08:27 |
General discussion | |
|
How to increase the +/-165A rms current limit to 250A+ rms (350-400A peak) by ev_motors on Sat, 2018-04-28 10:18 |
by ev_motors Sat, 2018-04-28 10:18 |
General discussion |
Pages
