You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Full Brake vs Switch Off by meisterpro on Mon, 2021-03-22 14:36 |
by meisterpro Mon, 2021-03-22 14:36 |
VESC Tool | ||
|
terminal command via UART for a gimbal by fredfred on Sat, 2021-12-18 20:49 |
by fredfred Sat, 2021-12-18 20:49 |
VESC Tool | ||
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset on Thu, 2022-08-04 01:44 |
by liminalsunset Thu, 2022-08-04 01:44 |
General discussion | ||
|
Can't find good parameters for FOC detection by Kabroc on Thu, 2020-04-30 16:28 |
by Kabroc Thu, 2020-04-30 16:28 |
VESC Tool | ||
|
Switchign frequency issue? by Maxid on Thu, 2020-12-03 11:47 |
by Maxid Thu, 2020-12-03 11:47 |
VESC Firmware | ||
|
Flipsky 75100 rebooting under load by SpacePT on Tue, 2022-07-26 14:47 |
by SpacePT Tue, 2022-07-26 14:52 |
Third Party Hardware | ||
|
UART Safety Feature by jaghori.sasan on Wed, 2019-09-04 18:45 |
by jaghori.sasan Wed, 2019-09-04 18:45 |
VESC Tool | ||
|
*newbie* motors keep running backwards randomly when switch off, and then back on. Embarrassing. by Nikolas Lamshed on Sun, 2021-06-20 13:36 |
by Nikolas Lamshed Sun, 2021-06-20 13:36 |
General discussion | ||
|
Connecting handlebar controlls by mannberg on Thu, 2022-03-10 14:57 |
by mannberg Thu, 2022-03-10 14:57 |
General discussion | ||
|
HFI Tuning - "Start Voltage" Question by drummerboy5408 on Sat, 2022-11-12 03:12 |
by drummerboy5408 Sat, 2022-11-12 03:12 |
General discussion | ||
|
Changing minimum duty cycle prevents VESC from connecting via USB while ADC throttle is connected by shimdidly on Sun, 2017-10-15 00:48 |
by shimdidly Sun, 2017-10-15 00:48 |
VESC Tool | ||
|
Calculator by kstuck on Tue, 2019-12-10 18:30 |
by kstuck Tue, 2019-12-10 18:30 |
General discussion | ||
|
connecting vesc tool with Prototipo by Govert on Thu, 2020-07-02 19:43 |
by Govert Thu, 2020-07-02 19:43 |
General discussion | ||
|
vesc 100250 Off-the-shelf motor by cuaxr on Mon, 2021-10-25 11:59 |
by cuaxr Mon, 2021-10-25 11:59 |
General discussion | ||
|
Serial Communication in Non-RT System by Jack_Li on Fri, 2019-07-05 15:58 |
by Jack_Li Fri, 2019-07-05 15:58 |
VESC Firmware | ||
|
Basic VESC troubleshooting (postmortem?) by N_COUNTER on Tue, 2023-03-14 10:58 |
by N_COUNTER Tue, 2023-03-14 11:01 |
General discussion | ||
|
How can I get current data from VESC to stm32f446re by hyedo on Sun, 2022-01-23 19:38 |
by hyedo Sun, 2022-01-23 19:38 |
General discussion | ||
|
Change some VESC configurations by nltb on Fri, 2020-09-11 13:39 |
by nltb Fri, 2020-09-11 13:39 |
VESC Firmware | ||
|
FSESC seems to be speed limiting my motor by 5amsung4 on Sat, 2022-09-03 18:50 |
by 5amsung4 Mon, 2022-09-05 07:51 |
VESC Tool | ||
|
Coging by lizardmech on Mon, 2017-07-03 15:29 |
by lizardmech Mon, 2017-07-03 15:29 |
VESC6 Beta |
Pages
