You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Can't get motor to run using COMM port on vesc 6 MKVI and arduino mega with a potentiometer and SolidGeeks UART library by Kokonenen on Thu, 2023-03-30 11:41 |
1 |
by Kokonenen Thu, 2023-03-30 16:19 |
General discussion | |
|
how I can connect 4 vesc using CAN and how connect vesc to PC via CAN bus? by Chanyoung Jung on Mon, 2020-03-09 08:12 |
1 |
by hexakopter Sat, 2020-04-18 13:12 |
General discussion | |
|
drill batteries in series with Flipsky 75100 by alexkid on Sat, 2022-05-14 15:41 |
1 |
by skyline1970 Thu, 2022-11-24 21:41 |
General discussion | |
|
Can't connect via Bluetooth anymore. by Stock88 on Wed, 2024-05-01 19:45 |
1 |
by electricfox Thu, 2024-05-02 10:08 |
General discussion | |
|
ADC TMM Sensor Voltage fluctuation by gianni on Sun, 2019-06-23 16:09 |
1 |
by gianni Mon, 2019-09-23 14:52 |
General discussion | |
|
Understanding VESC Hardware and $40 VESC target by ripperpc on Thu, 2020-02-27 06:41 |
1 |
by vadicus Mon, 2020-03-23 20:18 |
Third Party Hardware | |
|
Brake rpm minimum by mcspikesky on Sat, 2023-07-22 22:51 |
1 |
by mcspikesky Tue, 2023-07-25 22:03 |
General discussion | |
|
Esc does not reply by nemethLali on Sun, 2021-08-01 16:07 |
1 |
by nemethLali Fri, 2021-08-06 22:18 |
Third Party Hardware | |
|
PPM mapping not working by Andytttt on Thu, 2020-01-09 05:58 |
1 |
by frank Mon, 2020-01-27 21:06 |
VESC Tool | |
|
Wand firmware 1.3 by peacue on Mon, 2021-11-22 09:59 |
1 |
by frank Mon, 2021-11-22 12:56 |
VESC Firmware | |
|
VESC VI plus - No usable power / under voltage fault after pwr delivery by velolac on Sun, 2020-07-12 19:37 |
1 |
by velolac Sat, 2020-08-29 21:51 |
VESC Original Hardware | |
|
VESC Firmware update not working by timhermanson94 on Wed, 2019-07-31 18:42 |
1 |
by skyline1970 Fri, 2019-08-02 15:22 |
VESC Firmware | |
|
FSESC 4.12 oscillating and making noise by hichemhlm on Sun, 2020-03-29 13:33 |
1 |
by hichemhlm Sun, 2020-12-27 12:19 |
General discussion | |
|
I can't communicate with the VESC-Clone by Savavit on Sun, 2019-10-27 17:42 |
1 |
by vadicus Thu, 2019-11-07 06:48 |
Third Party Hardware | |
|
Controling the Vesc via Uart and Matlab? by Michael Hamm on Mon, 2022-01-24 16:47 |
1 |
by Fikret Sonmez Sat, 2022-07-30 06:14 |
General discussion | |
|
Diagnosing FSESC4.20 dead/weird phase (?) by josephduchesne on Sun, 2022-09-18 23:52 |
1 |
by skyline1970 Thu, 2022-11-24 20:23 |
Third Party Hardware | |
|
Flipsky 75200 ALU not booting up by Metastasis on Wed, 2023-09-20 15:45 |
1 |
by Metastasis Wed, 2023-09-20 17:18 |
VESC Firmware | |
|
Driving two motors with 75/300 by cmarc on Wed, 2019-10-16 17:32 |
1 |
by benjamin Fri, 2019-10-18 10:37 |
VESC Original Hardware | |
|
VESC tool Data log / CSV by Ole Skov on Mon, 2020-05-25 19:47 |
1 |
by mpater Sat, 2021-12-25 11:25 |
VESC Tool | |
|
Unable to enable Servo Out on VESC 6 Mk5 by kangalow on Thu, 2021-01-07 20:26 |
1 |
by kangalow Mon, 2021-01-11 23:15 |
VESC Firmware |
Pages
