You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
SPINTEND UBOX 100v100a x2 or Flipsky 75100 100v100a x2 by DuckyTheDuck on Mon, 2022-09-26 12:07 |
4 |
by primarc1982 Sat, 2026-05-09 07:16 |
General discussion | |
|
Vesc tool not working by faheemift on Sun, 2021-02-14 14:44 |
4 |
by faheemift Wed, 2021-04-14 22:59 |
General discussion | |
|
Lowest power/smallest available 3rd party board? by doctarr on Sun, 2021-03-07 15:28 |
4 |
by doctarr Mon, 2021-03-08 12:38 |
Third Party Hardware | |
|
Can't seem to downgrade firmware on my VESC 6 MKV by curiousgeorge on Thu, 2021-12-02 08:46 |
4 |
by curiousgeorge Fri, 2021-12-03 19:00 |
VESC Firmware | |
|
Merry Christmas! by frank on Fri, 2017-12-22 14:31 |
4 |
by ThierryGTLTS Sun, 2017-12-24 14:34 |
General discussion | |
|
Standby - consumption when battery is conencted by derbe on Thu, 2019-09-26 14:07 |
4 |
by frank Mon, 2020-01-27 20:48 |
Feature Requests | |
|
How do I compile the VESC Tool? by ipbyrne on Wed, 2019-07-24 16:58 |
4 |
by a.dahhak Fri, 2021-01-01 15:25 |
VESC Tool | |
|
Custom hardware flash problems by brightlightbeam on Mon, 2021-01-25 17:25 |
4 |
by brightlightbeam Thu, 2021-01-28 12:00 |
Third Party Hardware | |
|
FSESC6.6+ Over Voltage Fault 80mm Motors by Yomiel on Fri, 2020-03-20 03:45 |
4 |
by thefallen Mon, 2021-03-01 16:47 |
General discussion | |
|
VESC on 48V 1500W HUB motor by jordanlow on Sat, 2019-01-12 14:52 |
4 |
by jordanlow Thu, 2019-01-24 04:14 |
VESC Original Hardware | |
|
VESC 6 hi voltage problem by mike on Fri, 2018-05-04 11:34 |
4 |
by mike Tue, 2018-05-08 19:31 |
General discussion | |
|
Cant get Data on VESC Dash 35B by CommanderLee on Thu, 2026-03-26 00:42 |
4 |
by benjamin Tue, 2026-06-16 21:01 |
VESC Original Hardware | |
|
Starting rotation by changing duty cicle- current increases shortly (ms) and dcreases immediately to 0A by simon_snow on Wed, 2021-10-06 22:15 |
4 |
by simon_snow Fri, 2021-10-08 12:49 |
General discussion | |
|
E vehicle setup by jordanlow on Wed, 2019-03-20 10:33 |
4 |
by jordanlow Wed, 2019-03-20 16:18 |
General discussion | |
|
Flipsky can't connect to vesc tool by vescbeginer on Fri, 2024-08-02 20:16 |
4 |
by Bbonsack Tue, 2026-05-26 02:05 |
VESC Tool | |
|
Porting to a newer STM32 by TechAUmNu on Wed, 2020-09-16 12:38 |
4 |
by STEPHY AKKARA Thu, 2022-04-14 07:57 |
VESC Firmware | |
|
Roll-to-start VESC by dsuresh on Fri, 2021-03-12 21:05 |
4 |
by robertkovax Fri, 2023-11-10 16:57 |
General discussion | |
|
E-Bike Throttle connect with Regenerative Braking by E-Toxx on Sat, 2017-09-09 09:38 |
4 |
by Jacki Villis Thu, 2019-05-16 14:43 |
General discussion | |
|
My First ride! by Necromenz on Thu, 2017-06-15 15:30 |
4 |
by josh Mon, 2017-07-17 04:25 |
VESC6 Beta | |
|
Switching frequency data by petertaylor on Thu, 2018-11-08 00:53 |
4 |
by petertaylor Tue, 2018-12-25 20:28 |
VESC Firmware |