You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Autodetection algorithm by Griffen on Thu, 2019-01-03 18:44 |
2 |
by Gmack Fri, 2020-09-18 16:39 |
VESC Tool | |
|
<SOLVED> Terms defined / bldc "vs." vesc_tool by Gos1 on Tue, 2023-06-27 12:32 |
2 |
by Gos1 Fri, 2024-01-26 10:54 |
General discussion | |
|
mksvesc 84200 by Nubi on Sat, 2024-08-10 00:48 |
2 |
by Huang_jh Thu, 2024-10-17 12:55 |
Third Party Hardware | |
|
Firmware update for mac needed. by RustyHook on Wed, 2022-03-16 17:50 |
2 |
by RustyHook Wed, 2022-03-16 17:54 |
VESC Firmware | |
|
New need help by VinnyF on Tue, 2019-12-10 13:16 |
2 |
by tex Wed, 2019-12-11 17:19 |
Third Party Hardware | |
|
Vedder forums or Vesc forums? by Eric on Wed, 2017-09-13 14:39 |
2 |
by frank Mon, 2017-09-18 10:12 |
General discussion | |
|
motor not running smoothly, it makes little "steps" by nomadaomni on Mon, 2024-11-18 15:08 |
2 |
by nomadaomni Tue, 2024-11-19 12:51 |
General discussion | |
|
Regen question by proget.snc on Thu, 2021-09-02 14:36 |
2 |
by proget.snc Fri, 2021-09-03 11:50 |
General discussion | |
|
Brake Current Command Adjustments by josh on Fri, 2019-05-17 21:37 |
2 |
by josh Wed, 2019-06-05 17:14 |
General discussion | |
|
Flipsky nrf51288 by Idoff on Tue, 2018-12-11 21:33 |
2 |
by frank Mon, 2019-02-18 09:00 |
VESC Tool | |
|
Hall count drift by xachmo on Mon, 2018-03-26 07:17 |
2 |
by xachmo Wed, 2018-03-28 21:26 |
VESC Original Hardware | |
|
Can I change control mode on the fly through the UART port? by spork on Wed, 2019-03-13 02:24 |
2 |
by spork Wed, 2019-03-13 15:41 |
General discussion | |
|
Controlling multiple VESC over SPI by ttufuor on Mon, 2019-11-18 04:37 |
2 |
by Danny Bokma Fri, 2020-01-24 18:29 |
VESC Original Hardware | |
|
Suggestion for new forum area by Snabelost on Thu, 2022-10-06 23:55 |
2 |
by Snabelost Tue, 2022-10-11 18:30 |
General discussion | |
|
6 Phase Motor - How to Drive it? by vitormhenrique on Wed, 2020-02-19 05:47 |
2 |
by Badkad Fri, 2020-03-20 19:36 |
General discussion | |
|
Vesc motor resistance value by HiandHello on Wed, 2023-02-15 07:45 |
2 |
by HiandHello Wed, 2023-02-15 22:57 |
VESC Original Hardware | |
|
Setup for very slow < 100RPM on Maytech 6365 Motor. by jason3w on Tue, 2020-09-01 10:52 |
2 |
by asapereira Mon, 2020-09-14 10:26 |
VESC Tool | |
|
Need help please / Trampa Spur Gear Drive/ VESC 6 MkIV by Sektooor on Sat, 2020-08-22 14:22 |
2 |
by Sektooor Mon, 2020-08-24 01:49 |
VESC Firmware | |
|
Wrong HW version selected during FW update by babyboi on Sat, 2018-12-15 21:30 |
2 |
by babyboi Sat, 2018-12-22 03:55 |
VESC Tool | |
|
Firmware 3.37 too old, unable to Connect VESC_Tool by Nico Isn on Wed, 2018-04-18 11:17 |
2 |
by Nico Isn Fri, 2018-04-20 16:31 |
VESC Firmware |
Pages
