You are here
Feature Requests
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
uROS support by neuromancer2701 » Wed, 2019-11-06 21:17 |
0 |
by neuromancer2701 Wed, 2019-11-06 21:17 |
|
|
safety switch by Ralph Luckwaldt » Mon, 2019-10-21 13:15 |
1 |
by frank Mon, 2019-10-21 20:58 |
|
|
DC to AC pure-sine inverter mode by shaman » Fri, 2019-10-18 15:06 |
0 |
by shaman Fri, 2019-10-18 15:06 |
|
|
Wand odometer by hans_maier » Sat, 2019-09-14 15:20 |
3 |
by gianni Mon, 2019-09-23 15:19 |
|
|
Ramp time in profiles by Stupidspencer » Fri, 2019-09-13 20:41 |
1 |
by frank Wed, 2019-09-18 16:46 |
|
|
Handbrake when activating brake standstill by Pimousse » Mon, 2017-09-11 09:50 |
16 |
by frank Wed, 2019-09-18 16:39 |
|
|
Read erpm of motor through motor tachometer by jordanlow » Tue, 2019-04-30 15:18 |
1 |
by Teslafly Sat, 2019-07-20 00:44 |
|
|
Dual control loop with magnetic encoders by wall0069 » Sun, 2019-06-02 05:39 |
0 |
by wall0069 Sun, 2019-06-02 05:39 |
|
|
ERPM Limit Update Over CAN by josh » Sun, 2019-06-02 01:48 |
1 |
by josh Sun, 2019-06-02 02:05 |
|
|
Support for AMC1301 powered from bootstrap by antonchromjak » Thu, 2019-04-04 22:46 |
2 |
by antonchromjak Fri, 2019-04-05 11:16 |
|
|
Enhance position and rpm control interface / protocol by brushlessjoe » Wed, 2019-03-20 21:54 |
0 |
by brushlessjoe Wed, 2019-03-20 21:54 |
|
|
Motion commands for controlling CNCs by andresv » Fri, 2017-09-08 10:35 |
2 |
by brushlessjoe Sun, 2019-03-17 21:29 |
|
|
Combat Robot Mods by BrianNave » Sun, 2019-02-24 17:03 |
0 |
by BrianNave Sun, 2019-02-24 17:03 |
|
|
Allow braking to override negative ramping time by Paul15578 » Wed, 2018-01-24 06:20 |
5 |
by benjamin Sat, 2019-02-23 10:14 |
|
|
Auto power shut down by Ecyclist » Thu, 2018-09-20 00:47 |
4 |
by sam.vanratt Sat, 2018-11-24 20:12 |
|
|
Vesc slow speed BLDC without coging by igisboard » Tue, 2018-10-09 18:38 |
1 |
by Dillon Mon, 2018-11-19 01:41 |
|
|
Better use of hall sensors. by ThierryGTLTS » Fri, 2017-10-20 17:18 |
2 |
by AfdhalAtiffTan Wed, 2018-10-24 02:16 |
|
|
Show actual encoder RPM by Enak » Fri, 2017-09-08 01:05 |
2 |
by Roger Wolff Sun, 2018-09-16 09:47 |
|
|
Single shunt by andreas » Wed, 2018-09-12 22:17 |
0 |
by andreas Wed, 2018-09-12 22:17 |
|
|
Foc openloop soft start by Alan oldguy » Fri, 2018-09-07 03:05 |
0 |
by Alan oldguy Fri, 2018-09-07 03:05 |
|
|
Ramping and idle control by dougm » Sat, 2018-09-01 16:22 |
0 |
by dougm Sat, 2018-09-01 16:22 |
|
|
Raw encoder output from UART by sprockmonty » Mon, 2018-08-13 16:45 |
0 |
by sprockmonty Mon, 2018-08-13 16:45 |
|
|
15S support (and more amps) by Torxed » Mon, 2018-07-16 12:06 |
9 |
by Torxed Sat, 2018-07-21 21:52 |
|
|
Configurable Beta factor for motor NTC. by Danny Bokma » Tue, 2017-09-05 21:29 |
11 |
by slapshot136 Sun, 2018-07-15 20:05 |
|
|
Defining when Watt-hour / Amp-hour Data are rezeroed by isabar » Sun, 2018-06-24 10:19 |
0 |
by isabar Sun, 2018-06-24 10:19 |
Log in to post new content in the forum.
