You are here
Third Party Hardware
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Custom hardware by aachner » Thu, 2019-12-19 15:15 |
5 |
by vadicus Thu, 2020-01-16 20:28 |
|
|
low voltage/power VESC by qdxiatao » Sun, 2019-12-29 09:27 |
2 |
by qdxiatao Mon, 2020-01-06 02:04 |
|
|
Maker X Mini VESC burned at 46V. My fault or shitty quality? by smileandbeware » Mon, 2019-11-18 10:53 |
3 |
by frank Thu, 2019-12-26 15:27 |
|
|
Motor controller commercial test benches by lopezcontreras » Mon, 2019-12-16 15:31 |
0 |
by lopezcontreras Mon, 2019-12-16 15:31 |
|
|
New need help by VinnyF » Tue, 2019-12-10 13:16 |
2 |
by tex Wed, 2019-12-11 17:19 |
|
|
Vesc 6.6 120a ADC2 pin out seems to be shorting..? by beetbocks » Tue, 2019-11-26 14:23 |
1 |
by frank Thu, 2019-12-05 11:25 |
|
|
Can't update firmware FSESC 4.12 by TimBilliet » Tue, 2019-11-26 21:52 |
1 |
by TechAUmNu Wed, 2019-11-27 14:47 |
|
|
Flipsky VESC-clone firmware udapte problems by gui-rider » Sun, 2019-04-28 22:39 |
4 |
by avsha Fri, 2019-11-22 06:55 |
|
|
Abi encoder?? by Vigneshwar » Wed, 2019-11-20 06:10 |
0 |
by Vigneshwar Wed, 2019-11-20 06:10 |
|
|
I can't communicate with the VESC-Clone by Savavit » Sun, 2019-10-27 17:42 |
1 |
by vadicus Thu, 2019-11-07 06:48 |
|
|
VESC with 3 shunt by _johnny_ » Fri, 2019-11-01 18:57 |
0 |
by _johnny_ Fri, 2019-11-01 18:57 |
|
|
VESC hw_60 invert PWM. by _johnny_ » Fri, 2019-11-01 18:44 |
0 |
by _johnny_ Fri, 2019-11-01 18:47 |
|
|
EBESC 6.1 Remote wont connect and cant get past the error code port not recognized by flashg69777 » Tue, 2019-10-22 02:01 |
1 |
by frank Tue, 2019-10-22 11:13 |
|
|
IGBT Vesc FOC not working by ziumus » Sat, 2019-09-28 15:48 |
9 |
by bgdwiepp Sat, 2019-10-19 21:56 |
|
|
SpaceVESC, a modular small VESC by SpaceVESCproject » Wed, 2019-10-02 21:35 |
2 |
by frank Thu, 2019-10-17 11:47 |
|
|
VESC Design - Review and Bringup - 150V - 20A by ripperpc » Sat, 2019-09-21 17:30 |
1 |
by TechAUmNu Mon, 2019-09-30 14:34 |
|
|
Flipsky VESC 50A by CraigL100 » Fri, 2019-08-30 16:57 |
5 |
by CraigL100 Sat, 2019-09-14 12:10 |
|
|
Motor not spinning NO FAULTS by 123seaborder » Mon, 2019-06-10 21:46 |
1 |
by gogglespast Sat, 2019-09-14 08:34 |
|
|
Flipsky FSVESC Bricked? by dan.rowe » Thu, 2019-09-12 19:45 |
0 |
by dan.rowe Thu, 2019-09-12 19:45 |
|
|
ESC ceases operation after 40 sec ride by dekafive » Sun, 2019-08-25 22:25 |
1 |
by frank Mon, 2019-09-02 10:50 |
|
|
MAYTECH ESC6 200A runs fine on 6s, faults immediately on 12s by mxpro32 » Sun, 2019-06-30 21:39 |
3 |
by TechAUmNu Tue, 2019-08-13 10:21 |
|
|
MINI FOC from MakerX by YUTW » Thu, 2019-08-08 11:17 |
1 |
by speed3r Tue, 2019-08-13 10:17 |
|
|
Maytech 200A does not work in FOC, will a A200S work better? by doom » Wed, 2019-08-07 20:40 |
1 |
by TechAUmNu Fri, 2019-08-09 21:01 |
|
|
Hooking up two or more motor drivers to the same MCU by darkclaude » Thu, 2019-06-20 10:02 |
4 |
by skyline1970 Wed, 2019-07-31 13:53 |
|
|
Where does the 3.3v come from? by cnd » Sun, 2019-07-21 12:38 |
2 |
by cnd Wed, 2019-07-24 05:47 |
Log in to post new content in the forum.
