You are here
Third Party Hardware
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Gate driver by RSR » Sat, 2019-01-26 21:46 |
1 |
by bgdwiepp Fri, 2019-03-01 15:21 |
|
|
Flipsky6.6 usb not detected by krom68 » Sat, 2019-02-23 10:21 |
0 |
by krom68 Wed, 2019-02-27 19:43 |
|
|
3 shunt low side resistor configuration based on VESC 6 by jordanlow » Thu, 2019-02-14 16:42 |
1 |
by TechAUmNu Thu, 2019-02-14 18:31 |
|
|
Where to order plastic sleeve for VESC by braingame26 » Thu, 2019-02-07 16:34 |
0 |
by braingame26 Thu, 2019-02-07 16:34 |
|
|
Bus bar and heavy copper PCBs by lopezcontreras » Mon, 2019-01-28 17:40 |
3 |
by galp Thu, 2019-01-31 20:20 |
|
|
VESC 6 with 3 phase shunts to ground instead by shaman » Wed, 2019-01-30 21:23 |
2 |
by shaman Thu, 2019-01-31 15:33 |
|
|
4.12 Phase current/voltage sense mix up. Need assistance please. by shaman » Tue, 2019-01-29 14:58 |
2 |
by shaman Tue, 2019-01-29 16:24 |
|
|
maytech mto91hbm-nh motors hal sensor by nolander » Thu, 2019-01-10 00:01 |
1 |
by sunsam8 Thu, 2019-01-10 11:15 |
|
|
HW4.12 Firmware trouble by CTSchorsch » Wed, 2018-12-05 21:09 |
4 |
by sam.vanratt Fri, 2018-12-28 17:55 |
|
|
Custom VESC4.8 short circuit error by b4zz » Mon, 2018-12-17 10:26 |
4 |
by b4zz Wed, 2018-12-19 16:48 |
|
|
Cheap VESC (VESC 4.12 redesign) by shaman » Sun, 2018-12-09 16:16 |
7 |
by shaman Tue, 2018-12-18 21:48 |
|
|
Stream realtime data stops streaming by b.visser@studen... » Fri, 2018-09-14 16:09 |
1 |
by thewho Thu, 2018-12-13 21:27 |
|
|
How to upload firmware on MINI4 ? by john » Mon, 2018-11-12 10:55 |
1 |
by john Mon, 2018-11-12 11:59 |
|
|
Driving 2 BLDC motors with one MCU by Pimousse » Tue, 2018-06-26 15:42 |
13 |
by wkt Wed, 2018-10-17 14:02 |
|
|
SDRV - Dual 6.4 HW PCB by josh » Wed, 2018-03-07 07:39 |
42 |
by TechAUmNu Mon, 2018-10-15 22:04 |
|
|
Maytech VESC duty cycle & PID control problems by subodh.malgonde » Mon, 2018-10-01 11:49 |
1 |
by subodh.malgonde Tue, 2018-10-02 11:59 |
|
|
Maytech VESC 4.10 UART issues by LogixCraft » Tue, 2018-09-25 03:13 |
0 |
by LogixCraft Tue, 2018-09-25 03:13 |
|
|
Maytech VESC keeps startup spinning slowly by Snorreman » Mon, 2018-09-24 09:57 |
0 |
by Snorreman Mon, 2018-09-24 09:57 |
|
|
Custom 12S VESC seems to be power limiting or something by nickw1881 » Sat, 2018-08-25 07:40 |
4 |
by nickw1881 Tue, 2018-09-18 05:56 |
|
|
Maytech esc 5V rail reads 0.5v by hhhhghg » Fri, 2018-09-14 13:23 |
0 |
by hhhhghg Fri, 2018-09-14 13:23 |
|
|
Flipsky 4.12 Vesc in FOC mode? by Jonny254 » Sat, 2018-09-08 11:25 |
3 |
by Jonny254 Thu, 2018-09-13 05:48 |
|
|
VESC without Shunt Resistors/FOC by tul00985 » Mon, 2018-06-11 13:27 |
14 |
by tul00985 Mon, 2018-09-10 08:36 |
|
|
Uploaded the wrong firmware, now I need help to debug :P by Frazatto » Tue, 2018-08-21 15:46 |
12 |
by Frazatto Tue, 2018-09-04 19:33 |
|
|
VESC 6 With AS5047 encoder by Geir Henriksen » Tue, 2018-07-31 00:09 |
2 |
by frank Mon, 2018-08-20 09:32 |
|
|
External power-side board by HansPeterHaastrup » Mon, 2018-07-30 14:53 |
5 |
by HansPeterHaastrup Mon, 2018-07-30 18:23 |
Log in to post new content in the forum.
