You are here
Third Party Hardware
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Red Flashing Light? by givol » Sat, 2019-06-29 19:01 |
2 |
by frank Sun, 2019-07-21 18:25 |
|
|
copy setup from one vesc to another? by curtm » Mon, 2019-07-08 20:33 |
3 |
by district9prawn Sat, 2019-07-20 23:44 |
|
|
Flipsky 4.12 suddenly/randomly brakes by MetaMind » Thu, 2019-07-18 17:01 |
1 |
by TechAUmNu Sat, 2019-07-20 23:36 |
|
|
Motor spins only with outside help by asaf123098 » Thu, 2019-04-04 06:52 |
4 |
by dekafive Thu, 2019-06-20 11:36 |
|
|
Troubleshooting Newborn VESC by vadicus » Tue, 2019-04-09 02:13 |
3 |
by vadicus Tue, 2019-05-14 02:06 |
|
|
Flipsky losing its settings by jrowe » Tue, 2019-04-16 00:34 |
0 |
by jrowe Tue, 2019-04-16 00:34 |
|
|
Axiom: 100+kW controller by paltatech » Sat, 2019-04-13 17:09 |
1 |
by thewho Sun, 2019-04-14 00:48 |
|
|
Massive overshoot in BLDC current control by chris1seto » Tue, 2019-04-09 20:10 |
2 |
by frank Thu, 2019-04-11 11:40 |
|
|
Lack of throttle control / too fast by mgisch » Mon, 2019-04-01 05:57 |
6 |
by mgisch Wed, 2019-04-03 09:53 |
|
|
4 BLDC for 1 VESC by mac_cros » Wed, 2019-03-20 16:45 |
8 |
by tul00985 Wed, 2019-04-03 08:32 |
|
|
Phase A not working and GVDD_OV/GVDD_UV DRV faults by chocol4te » Mon, 2019-04-01 15:32 |
0 |
by chocol4te Mon, 2019-04-01 15:32 |
|
|
Video Live Streams of a dual drive based on stm32f429 by mkschreder » Sat, 2019-03-30 16:25 |
0 |
by mkschreder Sat, 2019-03-30 16:28 |
|
|
Driving Issues Due To Reversed Current Amplification by F4metz » Mon, 2018-12-17 16:45 |
1 |
by moto_guy Sun, 2019-03-17 02:39 |
|
|
Custom Hardware - FET shoot-through problem - oscilloscope captures by ben5243 » Tue, 2019-02-19 03:58 |
2 |
by TechAUmNu Sat, 2019-03-16 00:27 |
|
|
Fault finding on failed VESC by dmcke5 » Sun, 2019-02-17 01:57 |
2 |
by benjamin Wed, 2019-03-13 10:00 |
|
|
MICRO Module by F4metz » Sat, 2019-03-02 15:10 |
3 |
by chuttney1 Sun, 2019-03-03 18:54 |
|
|
SPI encoder on MIN4 by john » Wed, 2018-11-14 11:31 |
1 |
by F4metz Sat, 2019-03-02 14:18 |
|
|
Gate driver by RSR » Sat, 2019-01-26 21:46 |
1 |
by bgdwiepp Fri, 2019-03-01 15:21 |
|
|
Flipsky6.6 usb not detected by krom68 » Sat, 2019-02-23 10:21 |
0 |
by krom68 Wed, 2019-02-27 19:43 |
|
|
3 shunt low side resistor configuration based on VESC 6 by jordanlow » Thu, 2019-02-14 16:42 |
1 |
by TechAUmNu Thu, 2019-02-14 18:31 |
|
|
Where to order plastic sleeve for VESC by braingame26 » Thu, 2019-02-07 16:34 |
0 |
by braingame26 Thu, 2019-02-07 16:34 |
|
|
Bus bar and heavy copper PCBs by lopezcontreras » Mon, 2019-01-28 17:40 |
3 |
by galp Thu, 2019-01-31 20:20 |
|
|
VESC 6 with 3 phase shunts to ground instead by shaman » Wed, 2019-01-30 21:23 |
2 |
by shaman Thu, 2019-01-31 15:33 |
|
|
4.12 Phase current/voltage sense mix up. Need assistance please. by shaman » Tue, 2019-01-29 14:58 |
2 |
by shaman Tue, 2019-01-29 16:24 |
|
|
maytech mto91hbm-nh motors hal sensor by nolander » Thu, 2019-01-10 00:01 |
1 |
by sunsam8 Thu, 2019-01-10 11:15 |
Log in to post new content in the forum.
